Items Per Page:
6 Results (Viewing 1 - 6 of 6)
Stainless Steel Gen 7 Sea Pump for Mercury 496
Your Price:
$495.99

Stainless Steel Gen 7 Plus Sea Pump for Mercury 350, 496 and 502 Mag

625-4132

Stainless Steel Gen 7 Plus Sea Pump for Mercury 350 Mag, 496 Mag / HO, 8.2L Mag and 502 Mag (No Pulley)

oem to hardin comparison

The NEW and IMPROVED Gen 7 Plus Sea Pump now includes dual seals and dual bearings. The bearing are also 40% larger than OEM bearings leading to even longer pump life!

NOTE:  YOU CAN PURCHASE THE MODEL WITH PULLEY PRE-INSTALLED (625-4131) BY CLICKING HERE.

  • 100-percent factory leak tested to ensure OEM dependability
  • Premium SPEC-approved quality components
  • Premium SPEC-quality seals: utilizing OE face materials provides exceptional heat transfer and low friction
  • Endurance-quality bearings: severe-duty, precision-ground and lubricated Heat-treated bearing shafts to match rollers
  • High-quality, protective packaging

For a number of years now the factory sea pumps have been plagued with a design flaw that made each factory pump a throw away non serviceable item. While the impeller could be serviced it is the factory body that wears out prematurely. Without the proper tolerances these units just won’t pump water. Well, Hardin Marine, the largest manufacturer of all Stainless Steel Sea Pumps set out to again solve the short comings of OEM equipment. By developing a stainless steel 316 heat treated casting Hardin Marine was able to incorporate new dual stainless steel serviceable wear plates as well as the use of a standard common Mercury water impeller. These characteristics have now turned this pump into a serviceable replacement that will provide years of serviceable life span. And all at a fraction of the cost of the original pump. So if you’re out to update and upgrade to a pump that's designed to last a life time, look no further as it has arrived. Note: Impeller is included.

Stainless Steel Gen 7 Sea Pump for Mercury 496
Starting From:
$549.99

This Part has options, please click the button below to order.

Stainless Steel Gen 7 Plus Sea Pump for Mercury 350 Mag, 496 Mag / HO, 8.2L Mag and 502 Mag - With Pulley

625-413 + Option(s)

Stainless Steel Gen 7 PLUS Sea Pump for Mercury 350 Mag, 496 MAG /HO, 8.2L Mag and 502 Mag - With Pulley

oem to hardin comparison

The NEW and IMPROVED Gen 7 Plus Sea Pump now includes dual seals and dual bearings. The bearing are also 40% larger than OEM bearings leading to even longer pump life!

  • 100-percent factory leak tested to ensure OEM dependability
  • Premium SPEC-approved quality components
  • Premium SPEC-quality seals: utilizing OE face materials provides exceptional heat transfer and low friction
  • Endurance-quality bearings: severe-duty, precision-ground and lubricated Heat-treated bearing shafts to match rollers
  • High-quality, protective packaging

For a number of years now the factory sea pumps have been plagued with a design flaw that made each factory pump a throw away non serviceable item. While the impeller could be serviced it is the factory body that wears out prematurely. Without the proper tolerances these units just won’t pump water. Well, Hardin Marine, the largest manufacturer of all Stainless Steel Sea Pumps set out to again solve the short comings of OEM equipment. By developing a stainless steel 316 heat treated casting Hardin Marine was able to incorporate new dual stainless steel serviceable wear plates as well as the use of a standard common Mercury water impeller. These characteristics have now turned this pump into a serviceable replacement that will provide years of serviceable life span. And all at a fraction of the cost of the original pump. So if you’re out to update and upgrade to a pump that's designed to last a life time, look no further as it has arrived.

Note: This Part includes a pulley already assembled to the pump. The pulley included in the 625-4131 kit is 5-3/4" in outside diameter and WILL NOT replace pulleys from Axius models as the diameter is not the same. This pulley will also not replace the 7" larger diameter pulley #8M2013638. For 7" diameter Axius applications, purchase 625-4130. All product photos show 5-3/4" pulley unless labeled otherwise.

Frequently Asked Questions:

1. Does this pump come complete or do I need to buy any other parts?
A: This pump comes complete, with pulley and it will re-use your factory rear pump inlet.

2. What if my rear pump housing is worn badly?
A: This surface no longer mates to the the new impeller, so it does not matter, the rear housing is now only a water inlet and exit for your new pump.

3. Does this pump feature wear plates on both sides of the impeller?
A: Yes it does, this is a unique feature of this pump, this will allow you to service this pump for years to come without any housing damage.

4. Is any modification required to my factory mounting bracket?
A: No modification is required, this pump was engineered to accept the stock mounting bracket.

5. What impeller does this pump use?
A: This pump features an upgraded larger shaft and bearing assembly and is designed to use the standard Mercruiser sea pump impeller that has been around for 30 years and is readily available across the country. The pump includes an impeller.

6. What OEM sea pumps does this fit and what OEM #'s does it replace?
A:Fits Mercruiser Gen 7 Sea Water Pumps (2000-Present)305/350/377/496 C.I.D 5.0L/5.7L/6.2L/8.1LTBI/MPI/EFI/MAG/Horizon/Scorpio

Replaces Mercury Part Numbers: 468M0122655, 46-8M0118067, 46-862914T08, 46-862914T08P, 46-862914T12, 46-862914A13, 46-862914A13, 46-862914T10, 46-862914T11, 46-862914A13, 46-8M0139996, 46-8M0137217, 0M615000 THRU 0W300012, 0W300013 THRU 0W309999, 0W310000 THRU 0W649999, 0W650000 THRU 1A063239, 1A063240 & Up

7. I'm having possible suction issues with my Mercrusier Gen 7 Pump, what can I do?
A: Check out this link for a troubleshooting guide.

Deluxe Rebuild Kit for Gen 7 Sea Pump, Mercury 350, 496 and 502 Mag
Your Price:
$99.99

Deluxe Rebuild Kit for Gen 7 PLUS Sea Pump, Mercury 350, 496 and 502 Mag

625-4133

This rebuild kit is designed for use with the 625-4132 & 625-4131 GEN 7 PLUS Sea Pumps built 2020 and later. You can identify a Gen 7 Plus by the clear marking on the pump snout reading "Hardin Marine Gen 7 Plus"
Not for use on Stock pumps or older Model Gen 7 Sea pumps!

Deluxe Rebuild Kit for Gen 7 Plus Sea Pump, Mercury 350, 496 and 502 Mag


Rebuild a 625-4132 Stainless Steel Sea Pump with this kit. This deluxe kit includes wear plates, snap rings, seals, bearings, o-ring, impeller and gasket.


2 Stage Conversion for factory Gen 5 & 6 Sea Pumps
Your Price:
$1,299.99

2 Stage Sea Pump for Gen 4 & 6 Mercury Applications

625-4134

2 Stage Sea Pump for Gen 4 & 6 Mercury Applications

  • Dual 1" common inlet, 2 x 1" outlets

Note: Pulley is not included, image shown is rendering not actual item.

Replacement Shaft for Gen 3 Mercury Racing 1075 / 1300 Sea Pump 840053
Your Price:
$399.99

Replacement Shaft for Gen 3 Mercury Racing 1075 / 1300 Sea Pump 840053

625-4139

Replacement Shaft for Gen 3 1075/1300 Mercury Racing Sea Pump. Replaces OEM Mercury #840053

Permatex Aviation Form-A-Gasket No. 3 Sealant, 4 oz.
Your Price:
$14.99

Permatex Aviation Form-A-Gasket No. 3 Sealant, 4 oz.

625-4135

‎For close tolerance flanges, TYPICAL APPLICATIONS: Solid gasket dressing, Close fitting machined surfaces, Threaded connections, Aviation engines,, Products shall be ideally stored in a cool, dry location in unopened containers at a temperature between 8º to 28ºC (46º to 82ºF) unless otherwise labeled, Slow drying, Flexible setting, Withstands pressures to 5000 psi, For Aviation Engines, For Marine Engines

6 Results (Viewing 1 - 6 of 6)