730-GSOP 0-100 PSI Oil Pressure Sender For Livorsi Gauges
WARNING:
When installing the sender for your gauge onto the engine, you MUST NOT use any
sealant on the threads (i.e. teflon tape, pipe dope, RTV, etc.). Doing so will
prevent the sender from making clean contact with the engine, which will result
in either faulty or no operation of the gauge. The senders have a tapered pipe
thread, to create a seal, preventing leakage. This pipe thread also completes
the ground to the engine required for proper gauge operation.
|
|
730-GSOP80 0-80 PSI Oil Pressure Sender For Livorsi Gauges
WARNING:
When installing the sender for your gauge onto the engine, you MUST NOT use any
sealant on the threads (i.e. teflon tape, pipe dope, RTV, etc.). Doing so will
prevent the sender from making clean contact with the engine, which will result
in either faulty or no operation of the gauge. The senders have a tapered pipe
thread, to create a seal, preventing leakage. This pipe thread also completes
the ground to the engine required for proper gauge operation.
|
|
730-GSWT1/8 1/8" NPT 100-280F Water Temperature Sender For Livorsi Gauges (Mercury Match) WARNING: When installing the sender for your gauge onto the engine, you MUST NOT use any sealant on the threads (i.e. teflon tape, pipe dope, RTV, etc.). Doing so will prevent the sender from making clean contact with the engine, which will result in either faulty or no operation of the gauge. The senders have a tapered pipe thread, to create a seal, preventing leakage. This pipe thread also completes the ground to the engine required for proper gauge operation.
|
|
730-GSOT1/8 1/8" NPT 140 to 340F Oil Temperature Sender For Livorsi Gauges
WARNING:
When installing the sender for your gauge onto the engine, you MUST NOT use any sealant on the threads (i.e. teflon tape, pipe dope, RTV, etc.). Doing so will prevent the sender from making clean contact with the engine, which will result in either faulty or no operation of the gauge. The senders have a tapered pipe thread, to create a seal, preventing leakage. This pipe thread also completes the ground to the engine required for proper gauge operation.
|
|
730-GSWT3/8 3/8" NPT 100-280F Water Temperature Sender For Livorsi Gauges (Mercury Match) WARNING: When installing the sender for your gauge onto the engine, you MUST NOT use any sealant on the threads (i.e. teflon tape, pipe dope, RTV, etc.). Doing so will prevent the sender from making clean contact with the engine, which will result in either faulty or no operation of the gauge. The senders have a tapered pipe thread, to create a seal, preventing leakage. This pipe thread also completes the ground to the engine required for proper gauge operation.
|
|
730-GSFP6090 High Vibration Electric Fuel Pressure Sender
0-100 PSI, Autometer or Livorsi Gauges
Quite possibly one of the most important things to monitor while making those
high speed runs. Everyone knows fuel pressure is critical so always run the
correct senders to watch your gauge. All senders are 1/8" NPT.
|
|
730-GSFP/WP High Vibration Electric Fuel or Water Pressure Sender
0-15 PSI, Autometer or Livorsi Gauges
Quite possibly one of the most important things to monitor while making those
high speed runs. Everyone knows fuel pressure is critical so always run the
correct senders to watch your gauge. All senders are 1/8" NPT.
|
|
725-7019 1/2" O.D. Clamshell Cover for Hose, 4-1/4" x 1-1/2"
The hole spacing on this item is 1 1/8" x 3 1/16"
|
|
105-93683 + Option(s)
- Stainless Steel cover for 33C cables or 1/4" speedometer hose
- These covers are available in polished or powder-coated
- Overall length is 3 1/2", mounting holes are 1-7/8" on center.
|
|
730-GSBKK1 1/4", 3/8", 1/2" Bushing Kit for Livorsi Senders
|
|
865-5284 AutoMeter's GM LS engine gauge installation kits feature specialized components to ease the installation of an LS engine into your boat. Includes a full color installation guide that not only details the use of the included metric adapter fittings, short depth temperature sensor, and tachometer resistor, but also covers installation procedures for other commonly monitored parameters.
Each kit includes:
- 12mm x 1.5 to 1/8 in. NPT adapter
- 16mm x 1.5 to 1/8 in. NPT adapter
- Low profile electric temperature sender
- 10K 1/2 watt resistor (tach function)
|
|
105-93645 25 Foot Nylon 1/8" Hose Kit - Used with Mechanical Boost or Oil Pressure Senders & Gauges
|
|
730-GCH1/4 1/2" O.D. x 1/4" I.D. Push-On High Pressure Speedometer Hose 25 ft. Roll
No speedometer installation is complete without high pressure pitot tubing.
This high quality flexible pitot hose is available in both 1/8" and 1/4" and don’t forget that clamshell to cover the transition your
hose will make thru the hull.
Note: Sold in 25 ft. Rolls!
|
|
730-GCH1/8 1/4" O.D. x 1/8" I.D. Push-On High Pressure Speedometer Hose 25 ft. Roll
No speedometer installation is complete without high pressure pitot tubing.
This high quality flexible pitot hose is available in both 1/8" and 1/4" and don’t forget that clamshell to cover the transition your
hose will make thru the hull.
Note: Sold in 25 ft. rolls!
|
|
730-GPSESQ3 Convert your electronic automotive speedometer into a GPS speedometer with this GPS Pulse Antenna. The antenna receives GPS satellite signals and outputs the information to 8,000 or 16,000 pulse signal to your existing speedometer. This antenna eliminates connections to the transmission or the need to calibrate to your vehicles tire size. This fast update antenna receives signals 10Hz (10 per second) driving your speedometer to display your true speed (no pointer lag). This antenna is a stand alone device, which does not require a membership fee for GPS service. The antenna can be mounted under the dash or in an other hidden area as long as you verify the speedometer is working properly before permanently mounting the antenna. Accuracy and ease of installation makes this GPS Pulse Antenna an affordable solution if you are looking to upgrade to a GPS speedometer system.Convert your electronic automotive speedometer into a GPS speedometer with this GPS Pulse Antenna. The antenna receives GPS satellite signals and outputs the information to 8,000 or 16,000 pulse signal to your existing speedometer. This antenna eliminates connections to the transmission or the need to calibrate to your vehicles tire size. This fast update antenna receives signals 10Hz (10 per second) driving your speedometer to display your true speed (no pointer lag). This antenna is a stand alone device, which does not require a membership fee for GPS service. The antenna can be mounted under the dash or in an other hidden area as long as you verify the speedometer is working properly before permanently mounting the antenna. Accuracy and ease of installation makes this GPS Pulse Antenna an affordable solution if you are looking to upgrade to a GPS speedometer system.
|
|
730-GPSSQ3 Standard 1-second 1 HZ update with 4 ft harness and ring terminals,2 3/4" L x 2 3/8" W x 7/8" H. This receiver is used on Livorsi GPS gauges made prior to July 2015.
|
|
730-GPSSQ310X For use with the Livorsi GPS Speedometer with Odometer and Standard Livorsi GPS Gauges without Odometer made after July 2015. For Standard GPS Gauges without Odometer Made before July 2015 order 730-GPSSQ3 Fast 10 Hz 10x update with 4 ft harness with ring terminals, 2 3/4" L x 2 3/8" W x 7/8" H
|
|
730-GPSRAQ3VV Recommended for use with Livorsi Vantage View® Speedometers. Standard 1-second 1HZ update with 4 ft harness. Power and ground are pre-terminated and the signal wire is pre-terminated with a butt connector to connect to the NMEA 0183 input on the Master Harness. 2 3/4" L x 2 3/8" W x 7/8" H
|
|
730-GPSRAQ3VV Recommended for use with Livorsi Vantage View® Speedometers. Standard 1-second 1HZ update with 4 ft harness. Power and ground are pre-terminated and the signal wire is pre-terminated with a butt connector to connect to the NMEA 0183 input on the Master Harness. 2 3/4" L x 2 3/8" W x 7/8" H
|
|