602-10059DRPGLH TOP MOUNT PMGR HI TORQUE COUNTER CLOCKWISE ROTATION STARTER: For Use On Standard Rotation Engines.
Same Applications As 10059LH.
Replaces Mercruiser # 50-808011A4
Replaces Delco# 9000888
12V, 9-Tooth
Arco# 30459
Sierra# 18-5603
THIS STARTER CAN BE REPLACED WITH 10057LH
|
|
602-10032LH Counter ClockWise Rotation<2 Bolt mount>
Arco# 70107
OE# 50-808011A05
|
|
602-20110-100A Mercruiser 3.0L 1999-up 12V 105-Amp High Output Replacement for Merc #862030T
|
|
602-20119-100A Mercruiser 4.3L 6.2L 12V 105-Amp Saddle Mount 6-Groove 50mm Serpentine Pulley, Replaces Merc # 863
|
|
602-20131 12V 95-Amp Neg Ground supplied with 6-Groove Serpentine Pulley.
Replaces Merc #863077T01
|
|
602-89-101-16 This bearing installation tool replaces OE # 91-38628T and is used to install the pinion bearings in all Mercruiser sterndrives that have a pre-load pin driveshaft, and most Mercury outboard gearcases with a pre-load pin driveshaft.
|
|
602-17030 Replaces Mercruiser Diesel # 882481 & 879194371
Fits 1.7L Engines
OE# S114-869
|
|
602-89-101-30 This driver replaces OE # 91-30366T 1 and is used to install the gimbal bearing in Mercruiser MC-1, R, MR, Alpha One, and Bravo transoms.
|
|
602-89-101-33 Mercruiser Exhaust Bellows Expander Tool
This tool aids in the installation of the exhaust bellows.
Drive must be removed to use this tool.
Works for Mercruiser Alpha One and Alpha one Gen II as well as Bravo exhaust bellows.
|
|
602-VB500N-2 This Unit Is Supplied With # RES500L
Right Side Fill Reservoir And # 4 SAE
Inverted Flair Fittings.
This Is A High Volume Pump.
OE# 883166A 2
|
|
602-89-101-31 This driver head replaces OE # 91-32325T and is used to drive various other Mercruiser/ Mercury seal and bearing drivers.
|
|
602-89-101-19 This oil seal installation tool (seal driver) replaces OE # 91-43591T and is used to install both seals into MC-1, R, MR, and Alpha One sterndrive driveshaft housings. This will not work with an Alpha One Generation II sterndrive.
|
|
602-89-101-20 This oil seal driver replaces OE # 91-44110 and is used to install both seals into the water pump base of Mercruiser MC-1, R, MR, and Alpha One sterndrives. It will also work on most Mercury V6 outboard gearcases with a plastic water pump housing.
|
|
602-89-101-08 This bearing carrier oil seal driver replaces OE # 91-31108 and is used to install prop shaft seals in Mercruiser MC-1, R, MR, Alpha One, Bravo I, and Bravo III sterndrives. It is also used on Mercury V6 outboard gearcases.
|
|
602-WP1100 For GM Block In-Line 4 & 6 Cyl.,
Mercruiser, OMC 110, 120, 140.
MC #'s 65142A1, 814755, 880817
OMC #'s 3854017, 509356,984360, 986779, 980512
Sierra # 18-3575
Volvo # 3854017
OE# 884727
Sierra# 18-3575
|
|
602-SW88 Heavy Duty Solenoid For Delco
10MT Starters Used On Mercruiser,
OMC, Volvo & Many Others.
Rplc. Delco # 1114531
Short Solenoid (Metric)
Overall Lentgh To End Of Stud 4"
Arco# SW984
OE# 89-18080
Sierra# 18-5837
|
|
602-SW90 Heavy Duty Standard Solenoid For
Delco 10MT Starters Used On
Mercruiser, OMC, Volvo And
Many Others
Rplc. Long Solenoid
Overall Length To End Of Stud 4 3/4"
Arco# SW975
OE# 33261
Sierra# 18-5838
|
|
602-VB506N-2 This Is The Same Pump As PT500N-2 Used
On Mercruiser Applications, But This Unit
Is Supplied With # RES550 Left Side
Fill Reservoir. The Port Sizes Are 1/8"
NPT. Brass Fittings Can Be Supplied Upon
Request To Fit Your Specifications.
|
|
602-89-101-07 This shift shaft bushing tool replaces OE # 91-31107 and GLM # 90140. It removes and installs the shift shaft bushing on Alpha One Generation I sterndrives and some Mercury outboard gearcases.
|
|
602-89-101-18 This bearing retainer wrench (spanner tool) replaces OE # 91-43506 and GLM # 90240. It is used for removing and installing the driveshaft bearing retainer nut on some Mercruiser sterndrives and Mercury outboard gearcases.
|
|
