Hardin Marine

5/16"-24 Allen Bolt, 0.75" Long

5/16"-24 Allen Bolt, 1.00" Long, fine thread.

5/16-18" Stainless Steel Nylon Lock Nut - Half Height, Coarse Thread.

5/8" Left Hand Male Rod End

These rod ends are all stainless steel

This hose is designed to go from your bilge pump to your water dump It is flexible and easy to route.

Water bilge hose is sold by the foot, i.e add quantity of 6 for 6 ft. of hose.

Hose comes in maximum of 50 feet sections. Please specify if you want sections cut into specific lengths when ordering over 50 feet.

Marine Fuel Line Hose 5/8" I.D.

• This is true USCG approved marine grade fuel hose /li>
• This is A-2 grade hose

Don't take any chances with your investment Use only marine grade hose.

Fuel line hose is sold by the foot, i.e add quantity of 6 for 6 ft. of hose.

Hose comes in maximum of 50 feet sections. Please specify if you want sections cut into specific lengths when ordering over 50 feet.

Standard Water Hose 5/8" I.D.

This hose is perfect for plumbing the cooling system for most boats.

Water hose is sold by the foot, i.e add quantity of 6 for 6 ft. of hose.

Hose comes in maximum of 50 feet sections. Please specify if you want sections cut into specific lengths when ordering over 50 feet.

This hose is commonly used for venting or bilge dump.

Vent / Bilge hose is sold by the foot, i.e add quantity of 6 for 6 ft. of hose.

Hose comes in maximum of 50 feet sections. Please specify if you want sections cut into specific lengths when ordering over 50 feet.

5/8" Right Hand Male Rod End

These rod ends are all stainless steel

5/8" Stainless Steel Right Angle Fuel Vent

These stainless steel fuel vents offer an almost completely flush finish leaving no protruding hardware. Each vent comes complete with nut and backing plate. This vent is perfect in harsh corrosive environments.

5/8" Stainless Steel Straight Fuel Vent

These stainless steel fuel vents offer an almost completely flush finish leaving no protruding hardware. Each vent comes complete with nut and backing plate. This vent is perfect in harsh corrosive environments. Flange O.D. is 1.820".

5/8" Stainless Steel Washer.

5/8" Vent Adapter 90 Degree Angle Mount

Vent adaptors allow you to connect vent hoses from your valve covers or fuel pump to a flame arrestor assembly.

5/8-18" Stainless Steel Nylon Lock Nut - Half Height, Fine Thread.

50 Amp Mercury Style Circuit Breaker

These breakers are the most common marine units used on factory style as well as aftermarket marine engines and harnesses. Be careful not to exceed the original amperage rating of your existing harness.

500 Gallon Per Hour Bilge Pump

These Bilge Pumps are made in America, and are of top quality These pumps meet all necessary USCG requirements and are tested and specified by over 200 boat manufacturers.

The construction of these tiltable, race inspired stainless steel and billet aluminum helms feature an adjustable slip collar to accommodate different dash thicknesses while providing the ultimate in finished appearance. These steering posts bolt directly to a Char-Lynn hydraulic helm. This special model includes a bluetooth paddle trim system. Available in a dual steering wheel bolt pattern (Momo or Dino). Length is from the dash to the steering wheel mounting flange based on a 1" thick dash. Center steering wheel cover sold separately. All Stainless Steel helm assembly.

The construction of these tiltable, race inspired stainless steel and billet aluminum helms feature an adjustable slip collar to accommodate different dash thicknesses while providing the ultimate in finished appearance. These steering posts bolt directly to a Dan Foss hydraulic helm. This special model includes a bluetooth paddle trim system. Available in a dual steering wheel bolt pattern (Momo or Dino). Length is from the dash to the steering wheel mounting flange based on a 1" thick dash. Center steering wheel cover sold separately. All Stainless Steel helm assembly.

525 / 600SCI / 700SCI Mercury Replacement Header Gasket - Sold in Pairs

These gaskets are Graphite Impregnated designed to withstand the highest of temperatures on high horsepower applications. For those of you looking to do the job only once insist on Hardin Marine extreme-duty gaskets. Quite possibly the last gasket you’ll ever need.

Sold in Pairs

Seaward Standard Risers - Sold As A Pair

525 Seaward Tall Risers - Polished

5-3/4" Hide-A-Helm Steering Wheel Adapter

If you've been fortunate enough to see inside some of the most elite powerboats in the world toady such as Nor-Tec and Outerlimits, then you've probably noticed the ultra-cool dual switachble hidden helms they have.  Hardin Marine developed this system with two thoughts in mind.  First, dual helm steering systems up to now used two mounted steering posts fixed to both sides of the dash.  When one wasn't being used it stuck out of the dash as a safety hazard similar to a human harpoon.  By relocating the steering post beneath the surface of the dash and covering it with a smooth billet cap you now have a part that is worthy of existence on a million dollar boat.  Secondly, the easy removal of the steering wheel allows it to be stowed and locked beneath the cabin.  No steering wheel, means less chance of your boat being stolen.

5-3/4" OD x 1-5/8" Tall Flame Arrestor, Aluminum

This low profile USCG Approved flame arrestor is designed to fit all carburetors with a 5-1/8" air horn or neck. This unit has a 5-3/ 4" outside diameter and is 1-5/8" tall. This unit is constructed of aluminum and is not recommended for saltwater applications. This flame arrestor fits only the Quadrajet and Edelbrock 4bbl. carburetors it does not clear the Holley or Quickfuel J-tubes.

5-3/4" x 3" High Flame Arrestor, Aluminum (will fit inside std. scoops)

These flame arrestors both feature an aluminum mesh style USCG Approved construction Each unit is designed to fit a standard 5-1/8" carburetor neck while their outside dimension is 5-3/4". The 3" tall version has no fuel fume vent and fits perfectly inside most aluminum scoops. While the other version is 4" tall and has a fuel fume vent provision.

5-3/4" x 4" High Flame Arrestor with Vent Tube, Aluminum

• Each unit is designed to fit a standard 5-1/8" carburetor neck
• outside dimension is 5-3/4"
• The 4" tall and has a fuel fume vent provision
• Outer Vent Tube Diameter: 1/4"

These flame arrestors both feature an aluminum mesh style USCG Approved construction Each unit is designed to fit a standard 5-1/8" carburetor neck while their outside dimension is 5-3/4" and is 4" tall and has a fuel fume vent provision. Outer Diameter on the vent tube is 1/4" to match the fuel pumps its designed to attach to.

5-Bolt Grant Style Billet Aluminum Steering Wheel Adapter

• Made from Billet Aluminum and powder-coated
• Adapter is 3-3/8" in Diameter and 1" Tall
• Designed to fit the 5-bolt Grant steering wheels 
• Features a 3-bolt mounting flange and 5-bolt steering wheel mount
• Each adapter includes a billet center cap which fits 2-1/8" cap hole
• Each adapter is supplied with stainless steel hardware

Need help installing your new adapter? Check out this handy tutorial!

Mayfair By Hardin Marine Helms - 6" Standard Steering Post Assembly

The construction of these race inspired billet aluminum and stainless steel helms feature an adjustable slip collar to accommodate different dash thicknesses while providing the ultimate in finished appearance.  These steering posts bolt directly to a Char-Lynn hydraulic helm.  Available in a dual steering wheel bolt pattern (Momo or Dino) or a conventional 3-bolt pattern.  Length is from the dash to the steering wheel mounting flange based on a 1" thick dash. Center steering wheel cover sold separately.