Livorsi Marine

Toggle Switch Boots

These weather tight rubber moisture seal boots offer protection and styling for virtually any dash assembly. Now available in a rainbow of colors. 15/32" - 32 Threads

• Operating Voltage: 9 to 36 Volts DC (brightness does not change)
• Internal digital switching power supply operates at 94% efficiency
• Housing Materials: Passivated 316 Stainless Steel with Polycarbonate Lens
• Standard Cable Length: 20 ft
• Lamp Life: 40000 Hours
• Warranty: 2 Years

0-100 PSI Oil Pressure Sender For Livorsi Gauges

WARNING:
When installing the sender for your gauge onto the engine, you MUST NOT use any sealant on the threads (i.e. teflon tape, pipe dope, RTV, etc.). Doing so will prevent the sender from making clean contact with the engine, which will result in either faulty or no operation of the gauge. The senders have a tapered pipe thread, to create a seal, preventing leakage. This pipe thread also completes the ground to the engine required for proper gauge operation.

0-80 PSI Oil Pressure Sender For Livorsi Gauges

WARNING:
When installing the sender for your gauge onto the engine, you MUST NOT use any sealant on the threads (i.e. teflon tape, pipe dope, RTV, etc.). Doing so will prevent the sender from making clean contact with the engine, which will result in either faulty or no operation of the gauge. The senders have a tapered pipe thread, to create a seal, preventing leakage. This pipe thread also completes the ground to the engine required for proper gauge operation.

1/2" O.D. x 1/4" I.D. Push-On High Pressure Speedometer Hose 25 ft. Roll

No speedometer installation is complete without high pressure pitot tubing. This high quality flexible pitot hose is available in both 1/8" and 1/4" and don’t forget that clamshell to cover the transition your hose will make thru the hull.

Note: Sold in 25 ft. Rolls!

1/4" Cutout LED Warning Light

1/4" O.D. x 1/8" I.D. Push-On High Pressure Speedometer Hose 25 ft. Roll

No speedometer installation is complete without high pressure pitot tubing. This high quality flexible pitot hose is available in both 1/8" and 1/4" and don’t forget that clamshell to cover the transition your hose will make thru the hull.

Note: Sold in 25 ft. rolls!

1/4", 3/8", 1/2" Bushing Kit for Livorsi Senders

1/8" NPT 100-280F Water Temperature Sender For Livorsi Gauges (Mercury Match)

WARNING:
When installing the sender for your gauge onto the engine, you MUST NOT use any sealant on the threads (i.e. teflon tape, pipe dope, RTV, etc.). Doing so will prevent the sender from making clean contact with the engine, which will result in either faulty or no operation of the gauge. The senders have a tapered pipe thread, to create a seal, preventing leakage. This pipe thread also completes the ground to the engine required for proper gauge operation.

1/8" NPT 140 to 340F Oil Temperature Sender For Livorsi Gauges

WARNING:
When installing the sender for your gauge onto the engine, you MUST NOT use any sealant on the threads (i.e. teflon tape, pipe dope, RTV, etc.). Doing so will prevent the sender from making clean contact with the engine, which will result in either faulty or no operation of the gauge. The senders have a tapered pipe thread, to create a seal, preventing leakage. This pipe thread also completes the ground to the engine required for proper gauge operation.

3/8" Cutout LED Warning Light, Super Bright

3/8" NPT 100-280F Water Temperature Sender For Livorsi Gauges (Mercury Match)

WARNING:
When installing the sender for your gauge onto the engine, you MUST NOT use any sealant on the threads (i.e. teflon tape, pipe dope, RTV, etc.). Doing so will prevent the sender from making clean contact with the engine, which will result in either faulty or no operation of the gauge. The senders have a tapered pipe thread, to create a seal, preventing leakage. This pipe thread also completes the ground to the engine required for proper gauge operation.

5/16" Cutout LED Warning Light

4 Pin Connector & Wire Harness 18 inch, 3 Pack for Livorsi Single Outboard Engine Gauge Kits

The Plug-In Connector feature which makes Livorsi's new Deutsch gauges unique make installation a breeze, saving you a lot of rigging time & frustration. This 3 pack goes perfectly with one of our Livorsi Engine Gauge Kits.

NOTE: Connectors sold separately from gauges. Most Livorsi Gauges except GPS Speedos and Mechanical Gauges will require this connector!

4 Pin Connector & Wire Harness 18 inch, 5 Pack for Livorsi Gauge Kits

The Plug-In Connector feature which makes Livorsi's new Deutch gauges unique make installation a breeze, saving you a lot of rigging time & frustration. This 5 pack goes perfectly with one of our Livorsi Gauge Kits.

NOTE: Connectors sold separately from gauges. Most Livorsi Gauges except GPS Speedos and Mechanical Gauges will require this connector!

4 Pin Connector & Wire Harness 18 inch, 9 Pack for Livorsi Dual Engine Gauge Kits

The Plug-In Connector feature which makes Livorsi's new Deutsch gauges unique make installation a breeze, saving you a lot of rigging time & frustration. This 9 pack goes perfectly with one of our Livorsi Dual Engine Gauge Kits.

NOTE: Connectors sold separately from gauges. Most Livorsi Gauges except GPS Speedos and Mechanical Gauges will require this connector!

High Vibration Electric Fuel Pressure Sender
0-100 PSI, Autometer or Livorsi Gauges

Quite possibly one of the most important things to monitor while making those high speed runs. Everyone knows fuel pressure is critical so always run the correct senders to watch your gauge. All senders are 1/8" NPT.

High Vibration Electric Fuel or Water Pressure Sender
0-15 PSI, Autometer or Livorsi Gauges

Quite possibly one of the most important things to monitor while making those high speed runs. Everyone knows fuel pressure is critical so always run the correct senders to watch your gauge. All senders are 1/8" NPT.