Generic

"This widely used lever operated hand pump features a swiveling spout and light back and forth pumping action for precise flow control. Suitable for use with fresh or salt water. 1/2" hose connection, self-priming to 10'."

GPM: 1.85

Sold: Each

The Flojet LF Plus design with an IP (Ingress Protection) rated cover and quick fit ports improves the installation process. With On-Demand (pressure switch shut-off) and a robust material selection suitable for handling a broad range of applications, these low flow pumps meet the market's variable demands.

• Self priming up to 6' (1.8m)
• Can run dry for extended periods of time without damage
• Low amp draw, ideal for battery powered applications
• Sealed pressure switch automatically starts and stops pump
• 2.66" H x 4.05" W x 6.57" L, 1.3 lbs
• 1.0 GPM @ 25 PSI

Description: Pump w/ RFI supression, GPM: 1, Volts: 12, Amps: 2.5

GPM: 3.3, Volts: 12V, Amps: 3.9 @ 10 psi

• Run dry protection up to 30 seconds
• Pump housing connects onto the standard 3" waste outlet
• 6' Power leads with plug may be permanently attached to the vehicle or battery clips may be attached for portability
• Discharge port is a standard garden hose connector and the macerator section grinds waste down to a particle size of 1/8" maximum
• Pump longer distances and empty your holding tanks into a portable tank, toilet, sewer clean-out port or septic tank

Volts: 12, Inlet: 3"

• RV macerator pump can empty a 30 gallon (115 liter) holding tank in 3 minutes
• Grinds waste into small particles for easy disposal
• Self-priming with a flow rate of 13 gpm (49 lpm)
• Pump can be permanently installed for easy holding tank evacuation into a toilet or plumbing clean out access

GPM: 13, Volts: 12, Amps: 16, Inlet: 3", Outlet: 1"

Molded black plastic. Designed with a flange molded into part to fit into hole, hiding raw or cut edges. Mounts with 4 screws. Bulk packaging.

Size: 4-1/4" dia. ", Hole: 2-1/2" dia. ", Case: 12

Sold: Each

Molded black plastic. Designed with a flange molded into part to fit into hole, hiding raw or cut edges. Mounts with 4 screws. Bulk packaging.

Size: 5-5/8" dia. ", Hole: 4" dia. ", Case: 12

Sold: Each

"Positive sealing ball scupper. Seal slotted to fit over 1-1/4" motorwell hole."

:

Sold: Each

This 2.3 gallon capacity air operated extractor can be used to remove a wide range of fluids, such as engine oil, brake fluid, antifreeze and more. Built in shut off valve to prevent overfilling. Comes complete with 5' of flexible hose, two rigid dipstick tubes and a brake bleeding kit. Both units can be used away from the air source by creating a vacuum and closing off the shut off valves until it's ready to use. Utilizes an integrated pump to create low pressure and can be used for extracting or dispensing fluid. Move the bi-directional valve to create a vacuum or move the valve in the opposite direction to create pressure to dispense.

Description: Extractor/Dispenser, Capacity: 2.3 Gal (8.8 L)

Sold: Each

Fluidampr Int. Harmonic Balancer Chevy LS1/LS6/LS2

• Material: Steel
• Finish: Black Zinc
• Keyway: None
• Bore Dia. Min/Max: 1.4818 / 1.4828
• Degree Marking Range: None
• OD: 6-1/4"
• Length: 2.637
• Engine Balance: Internal

You can't feel them or hear them, but harmonic vibrations are at work inside every internal combustion engine. That's not good. Similar to glass-shattering forces created by a high pitched note, harmonic vibrations cause metal fatigue and can cause significant power loss because crankshaft harmonics are transmitted to the camshaft and valvetrain. Control this power-robbing force with a Fluidampr harmonic damper that uses race proven vibration damping technology. A high viscosity silicone fluid surrounds a nylon-coated inertia ring inside a laser welded housing. All dampers are coated with a black zinc chromate finish for increased corrosion resistance. Timing marks - every two degrees from 50° BTDC to 10° ATDC with additional marks at 90, 180 and 270. Meets SFI 18.1 specs. Made In The USA.

Fluidampr Int. Harmonic Balancer GM / Chevy 6.2L LT4

• Crankshaft torsional vibration protection across RPM range. 
• Reduce risk of crankshaft failure & wear on critical engine parts. 
• Unleash lost torque and horsepower. 
• Replaceable crankshaft hub. 
• SFI 18.1 certified.
• Made in USA.

The steel damper is finished in a corrosion resistant black zinc chromate, then laser engraved with a Fluidampr – Made in the USA logo and SFI 18.1 credential. The front and rear bolt-on Supercharger and air-conditioning aluminum pulleys have a hard coat anodized finish.

Available in three sizes to fit any GROCO ARG Strainer, flush caps make flushing your raw water cooled equipment a snap. Temporarily replacing your existing strainer cap with a flush cap will allow you to easily connect a Port-O-Flush Jr.^® or garden hose to your system. Use flush caps to flush you raw water cooled equipment with Barnacle Buster^®, fresh water, or to aid in winterizing your system.
NOTE: Not intended to replace your existing strainer cap, for flushing use only.

Fits: Groco ARG 500, 750 & 755 strainers

Available in three sizes to fit any GROCO ARG Strainer, flush caps make flushing your raw water cooled equipment a snap. Temporarily replacing your existing strainer cap with a flush cap will allow you to easily connect a Port-O-Flush Jr.^® or garden hose to your system. Use flush caps to flush you raw water cooled equipment with Barnacle Buster^®, fresh water, or to aid in winterizing your system.
NOTE: Not intended to replace your existing strainer cap, for flushing use only.

Fits: Groco ARG 1500+ strainers

Chrome plated zinc. Sliding lock button. Reverse bevel with flush strike. Flush cup installs in 2" diameter hole. Supplied with black plastic spacer for optional surface mounting.

• Screw size for cup is #8
• case is #6
• OD cup is 2-1/4"
• case is 2-1/16" x 1-3/4"
• For door thickness of 3/4" to 1-1/8"

"For securely "Dogging" (fastening) deck hatches. Chrome plated brass and stainless steel lock nuts. Flush strike. O-ring seals for water resistance. Does not rattle when dogged down. Maximum hatch thickness 2"."

Size: 3-13/16" x 3", Fastener: #8

Sold: Each

"Injection molded ABS. Overall face dimension is 3-5/8" x 3-5/8". Hose/hole size 3". Carded."

Color: White, Fastener: #8 FH

Sold: Each

Material: Chrome Bronze, Size: 3-3/4" x 2-3/4" , Fastener: #8

Material: Chrome Bronze, Size: 3" x 2-1/4" , Fastener: #8

Material: Chrome Zinc, Size: 3" x 2-1/4" , Fastener: #8

Flange: 3" L x 2-1/4" W , Fastener: #6