Generic

Head Gasket

Description: Head Gasket: E/J V4 120-140hp '88-96, OMC# 340115

Sold: Each

Head Gasket

Description: Head Gasket: Yamaha V-6, YM 6G5-11181-00-00

Sold: Each

HEAD SCREW NYLON 1/4" Black

Seadog Head Screws have injection molded heads and stainless steel shafts.

Features:
• Head screw: 1/4"-20 x 7/8"
• Length: 1-3/8"

Head Screw Nylon 1/4" White

Seadog Head Screws have injection molded heads and stainless steel shafts. Available in black or white.

• Head screw: 1/4"-20 x 7/8"
• Length: 1-3/8"

Cast Stainless Steel Header Water Pressure T-Valve

The T-Valve is a spring/ball style water flow check valve designed to control the flow and time of release of the water into water injected exhaust headers thus rendering the headers dryer and hot at an idle when properly adjusted and allow water flow at the appropriately tuned higher engine RPM's. -8 AN Male Ports

Heat Exchanger CuNi Yanmar 4 x 19 Verify Length

Verify Length Before Ordering.

"Powder coated/stainless steel. Crimps 22-10 gauge heat shrink terminals. 9" Long.

The Quick Connect system can be used by anyone to install additional outlets or to replumb your boat or recreational vehicle. Whale Quick Connect fittings offer many benefits, all ensuring a high integrity plumbing system. The pipework's flexibility enables tight bends to be formed, hence reducing both the number of fittings and time required at installation. Whale Quick Connectsemi-rigid pipework offers the integrity of metal, but the usability of plastic, and is fully tested and recommended for use with the complete range of Whale fittings.

• Unique ?Double Gripper' design provides secure lifelong pipework retention even at excessive pressures


• The innovative ?cage collet' eliminates leaks where fittings are installed close to tight bends


• Collet has internal support ring ensuring o ring seal is held in position and does not distort or leak under pressure


• High integrity single piece moulding improves the strength of the fittings


• Outer sleeve incorporates collet cover, thus preventing accidental pipework release


• Collet clips are not necessary and therefore reduce installation time


• Pipework includes measured cut marks, designed to be a visual guide to ensure that fittings are pushed fully home

• Unique 'Double Gripper' design provides secure lifelong pipework retention even at excessive pressures


• The innovative 'cage collet' eliminates leaks where fittings are installed close to tight bends


• Collet has internal support ring ensuring o ring seal is held in position and does not distort or leak under pressure


• High integrity single piece moulding improves the strength of the fittings


• Outer sleeve incorporates collet cover, thus preventing accidental pipework release


• Collet clips are not necessary and therefore reduce installation time


• Pipework includes measured cut marks, designed to be a visual guide to ensure that fittings are pushed fully home

Description: "Heat Connector 1/2" Male -1/2" Female"

Sold: Each

Used for engine cooling, ice box, sink, shower drain lines, A/C, bilge and bait box. 2 spiral EPDM hose resists heat, cold, engine water additives and coolants. 50 psi. Max temp of 212° F. Black. 1 year warranty.

ID: 3/4", OD: 1-1/32", Length: 50', Working Pressure: 70#

Used for engine cooling, ice box, sink, shower drain lines, A/C, bilge and bait box. 2 spiral EPDM hose resists heat, cold, engine water additives and coolants. 50 psi. Max temp of 212° F. Black. 1 year warranty.

ID: 5/8", OD: 29/32", Length: 50', Working Pressure: 90#

Barrel collars for shafts - zinc "Heavy Duty"

Heavy Duty Clamp-On Oarlocks Zinc 1/2"

Seadog Heavy Duty Clamp-on Oarlocks are constructed of zinc plated steel and have a 1/2" diameter shaft. The clamp is adjustable to fit most oars. Available in pairs.

• Easily rotates to a towing position with a spring-loaded locking mechanism


• Convenient side crank handle has a large corrugated poly grip handle


• Maneuverability is obtained from offset swivel caster assembly with polypropylene dual wheels


• Complete with all mounting hardware


• Fits square tongues up to 3'' x 5''

Travel: 12", Mount: Bolt-on, Max Load: 1500 lbs.

Sold: Each

A range of compact, raw water resistant, multipurpose bronze pumps. With excellent self-priming capability, these pumps are ideal as cooling water pumps for marine engines, bilge pumps, deck wash pumps, fresh water pumps, fuel transfer pumps and other applications. Also ideally suited on shore to empty septic tanks, to flush clean and to fill water tanks.

Impeller: 09819B, Ports: 1-1/4" or 1-1/2" NPT, Volts: 12, Pump Type: F8B-8007

• With Cover


• 6" loop length


• Fuse sold separately

Rating: 60, Gauge: 8

Sold: Each

A: 4-1/4", B: 1", C: 1-1/4", D: 1-3/4", Fastener: #10 FH, Pack: 2

A: 6-1/16", B: 1-1/4", C: 1-9/16", D: 2-1/4", Fastener: 1/4" FH, Pack: 2

A: 8-1/16", B: 1-3/4", C: 2-1/4", Fastener: 5/16" FH

Heavy Duty Sea Goin' Poxy Putty - Extra Thick Adhesive Epoxy - 12 Ounces

This Epoxy putty is perfect for installation of jet drive intakes, rudder boxes,and/or repair of numerous items. This putty won't sag and is very consistent. It can be used for buildup and will cure on wet or dry surfaces. This putty is very high strength and may be sanded, drilled, and even painted.

Heavy Duty Sea Goin' Poxy Putty - 3 lbs / 1 Quart

This poxy putty is perfect for installation of jet drive intakes, rudder boxes, and/or repair of numerous items. This putty won't sag and is very consistent. It can be used for buildup and will cure on wet or dry surfaces. This putty is very high strength and may be sanded, drilled, and even painted.