152-O1101 O-RING, BOWL (PRE 1994, O-RINGS FITS INTO THE FACE OF THE BOWL, AT309 ONLY)
|
|
|
|
|
152-O3102 O-RING, BOWL TO SUCTION (OEM BERKELEY 1994 TO PRESENT)
Supersedes: 152-J0481
|
|
152-H200985 O-RING, HAMILTON 212, HAND HOLE COVER
|
|
152-H61464 O-RING, HAMILTON 212, SEAL FACE HOUSING
|
|
152-H200999 O-RING, HAMILTON 212, STATOR
|
|
152-H064726 O-RING, HAMILTON 212, WATER OFFTAKE
|
|
152-O1003 O-RING, HANDHOLE COVER, DOM
|
|
|
|
|
152-O5001 O-Ring, Nozzle Housing, Sd191, Sd203, Tj191
|
|
152-O5260 O-Ring, Nozzling Housing, 191af & Sd203af
|
|
152-O5035 O-Ring, Oil Reservoir Lid
|
|
152-O62080 O-Ring, Oil Reservoir To Suction 12s-Mr
|
|
152-O1301 O-RING, PLUG / HAND HOLE EXT.
|
|
152-O3001 O-RING, REVERSE CABLE PACKER
|
|
|
|
|
152-O3401 O-RING, SEAL FACE HOUSING, SD
|
|
|
|
|
152-O5320 O-Ring, Shaft To Preload Ring 12s-Mr
|
|
152-O5123 O-Ring, Shaft To Slinger Ring 12s-Mr
|
|
152-O5204 O-Ring, Shift Shaft Pin, Sd231
|
|
|
|
|
152-O3501 O-RING, STEERING TUBE SEAL
|
|
152-O5369 O-Ring, Teflon, Nozzle, 231af
|
|
152-O5363 O-Ring, Teflon, Nozzle, Sd203
|
|
|
|
|
152-O3801 O-RING, WATER TUBE, SD-312
|
|
152-O5172 O-Ring, Wear Plate, Sd203af
|
|
152-O3208 O-RING, WJ NOZZLE, YJ/WJ INSPECTION COVER
|
|
152-O3108 O-RING, YJ SEAL-PAC, WJ BEARING HOUSING
|
|
152-SC2507 Packing Follower (Set 2)
Supersedes: 152-J0498
|
|
152-SC3007 Packing Ring (5 Rings Per Set)
|
|
|
|
|
|
|
|
152-RA4701 PIN ASSEMBLY, UP / DOWN, TRIM
|
|
152-HA103170 PIN, COTTER (RS3501 [ MUST USE AT NUT] )
|
|
|
|
|
152-R3701 PIN, LOWER STEERING, REVERSE BUCKET
|
|
|
|
|
152-R5108 PIN, REVERSE PIVOT 10/32 THRD.
|
|
|
|
|
|
|
|
152-JT1011 PIVOT BLOCK, JET TRIM HYD. CYL.
|
|
152-RV1107 Pivot Bolt Shim .036, Sd231
|
|
152-T2101 Plastic 3/4 NPT Std Reverse Cable Packer
|
|
|
|
|
|
|
|
152-BN2210 Port Side Pivot Bolts (Best & SDR)
|
|
152-SC9000 Prime-A-Jet
Eliminate having to rev the engine after putting the boat in water due to pump being air locked. This is a must for drag racers, as it's a common problem with running a droop snoot. This installs by drilling and tapping the top side of the bowl about 2.5" back from suction housing flange. 1/4" NPT Thread
|
|
152-SHA1107 Pump Shaft Assembly w/B1007
|
|
