Serial 0B721206 Thru 0D805068 - Bravo Drives

Plate Puller 91-29310

Use as a guide to remove and install the gimbal bearing on the MC-1, R-MR, Alpha One, Alpha One Gen II, Blackhawk and all Bravo drive units.

Propeller Nut Tool 91-805457T1

Installs and removes the front propeller nut on the Blackhawk and Bravo Three drive units.

Supercedes: 91-805457, 91-8054571

Propeller Shaft Adaptor 91-61077T

Provides a wrench surface to turn the propeller shaft on the MC-1, R-MR, Alpha One, Alpha One Gen II, Balckhawk and all Bravo drive units.

Supersedes: 91-61077

Supercedes: 91-61077

Puller / Driver Assembly 91-90244A1

Removes and installs the drive shaft housing bearings and sleeves on all the Bravo and Blackhawk drive units. Assembly includes the following:
91-90777T1 Puller Jaws
91-90774 Puller Guide
91-90775 Puller Bolt
91-90244T Driver Guide
91-90773T

Puller Head 91-63616T

Remove the upper swivel shaft on MC-1, R-MR, Alpha One and Alpha One Gen II gimbal rings.
Bravo One, Bravo Two and Bravo Three High Performance drive units hinge pin puller.

Supercedes: 91-63616

Puller Jaw 91-34570

Replacement jaw for the 91-34569A1 Slide Hammer Puller Tool.

Puller Jaw 91-816242

Use with either the two prong or three prong puller on all Mercury MerCruiser drive units.

Retention Sleeve Removal Tool 91-862546

Removes the aluminum sleeve from the U-joint bellows of all the Bravo and Blackhawk drive units, Serial Number 0L999999 and below.

Roller Bearing Removal and Installation Tool 91-37292

Part of 91-31229A7 Bearing Removal and Installation Tool Assembly, use with the threaded puller rod or driver rod.

Seal Driver 91-813653T

Installs the U-joint oil seal into the bearing carrier. Also use to pilot the puller rod for the gear housing needle bearing installation on all the Bravo drive units.

Supersedes: 91-813653, 91-89868

Supercedes: 91-89868, 91-813653

Seal Driver, Bearing Carrier Seal 91-805372

Installs the seals in the Blackhawk and Bravo Three drive unit bearing carriers.

Seal Driver, Outer Propeller Shaft 91-805358T

Installs the seals in outer propeller shaft of the Bravo Three and Blackhawk drive units.

Supercedes: 91-805358

Seal Removal Tool 91-862064A1

Use to remove the needle bearing and oil seals in the bearing carrier of all the Bravo Three drive units.
25-805048 Replacement O-Ring

Shift Cable Adjustment Tool 91-12427T

Attaches over the shift cable. Use for proper Bravo drive unit shift cable adjustment at the shift plate.

Supercedes: 91-12427

Shift Cable Anchor Adjustment Tool 91-17262A1

Use to install and remove shift shaft bushings on all Bravo drive units.
91-17262A1 Core Wire Locating Tool
91-17263 Shift Cable Anchor Adjustment Tool

Shift Cable Anchor Adjustment Tool 91-17263

Shift Handle Tool 91-17302

Positions and removes the shift shaft on the Bravo One and Bravo Two drive units.

Shimming Tool 91-805462T

Measures the pinion height on the Blackhawk and Bravo Three drive units.

Supercedes: 91-805462

McGard Stern Drive Locks - Single Drive MerCruiser Alpha & Bravo Stern Drive Lock

• Overall Lock Length: .750"
• Thread Size: 7/16" - 20
• Hex Size: 5/8"
• Set of 1 Lock, 1 Key and 1 Cap

Stern drive theft is on the rise, don't take a chance on losing your favorite outdrive or prop, for that matter be safe not sorry. Simply replace one of the stern drive mounting nuts with a McGard lock. Stern drive locks are fully machined from high quality stainless steel and through-hardened. This proven design features a free-spinning collar that turns if attacked by gripping tools without loosening the lock. Give yourself the best protection available against stern drive theft. Ask for McGard Marine Locks by name.

Sleeve Installation Tool 91-818162

Installs the aluminum sleeve in the U-Joint bellows of all the Alpha One Gen II, Blackhawk and all Bravo drive units.