900-31F100-SHS 5/16"-24 Allen Bolt, 1.00" Long, fine thread.
|
|
625-4312
Replacement 496 Sea Pump Axius 7" Pulley and Mandrel Kit
This billet pulley is designed as a replacement for popular MerCruiser Axius applications. Will fit stock MerCruiser or Hardin Gen 7 Pump. For 350, 496, 502 Mag with 7" diameter Axius pulley applications only. Includes mandrel and bolts.
|
|
625-4234 Seal for Hardin Marine Gen 7 and Gen 8 Pumps
|
|
625-4203 This rebuild kit is designed for use with the 625-4102, 625-4132, 625-4131 & 625-4101.
Not for use on Stock pumps!
Standard Rebuild Kit for Gen 7 Sea Pump, Mercury 350, 496 and 502 Mag
Rebuild a 625-4101, 625-4102, 625-4131 and 625-4132 Stainless Steel Sea Pumps with this kit. This standard kit includes the wear plates, o-ring, impeller and gasket.
|
|
625-4204 This rebuild kit is designed for use with the 625-4102 & 625-4101 GEN 7 Sea Pumps built 2019 and earlier.
Not for use on Stock pumps or new Model Gen 7 PLUS Sea pumps!
Deluxe Rebuild Kit for Gen 7 Sea Pump, Mercury 350, 496 and 502 Mag
Rebuild a 625-4102 Stainless Steel Sea Pump with this kit. This deluxe kit includes wear plates, snap rings, seals, bearings, o-ring, impeller and gasket.
|
|
625-4278
Replacement 496 Sea Pump Pulley and Mandrel Kit
This billet pulley is designed as a replacement for popular MerCruiser applications. Will fit stock MerCruiser or Hardin Gen 7 Pump. For 350, 496, 502 Mag with 5-3/4" diameter pulley applications only. Includes mandrel and bolts. This kit includes #13 - #16 on the Gen 7 Sea Pump Breakdown. Replaces OEM Mercury# 8M0150724.
|
|
625-4209 If you are having trouble installing impellers in Gen 7 Sea Pumps this handy tool allow for easy installation in less than 30 seconds!
|
|
625-4241 Replacement shaft for Hardin Gen 7 Sea Pumps. NOTE: Will NOT replace factory Mercury shafts as the Hardin Pump design was reconfigured to fit an additional wear plate. Can only be used on Hardin pumps 625-4102 and 625-4101.
|
|
625-4242 Replacement bearing for Hardin Gen 7 Sea Pumps. NOTE: Will NOT replace factory Mercury bearings as the Hardin Pump design was reconfigured to fit an additional wear plate. Can only be used on Hardin pumps 625-4102 and 625-4101.
|
|
625-4243 Replacement snap ring for Hardin Gen 7 Sea Pumps. NOTE: Will NOT replace factory Mercury parts as the Hardin Pump design was reconfigured to fit an additional wear plate. Can only be used on Hardin pumps 625-4102 and 625-4101.
|
|
625-4244 Replacement seal for Hardin Gen 7 Sea Pumps. NOTE: Will NOT replace factory Mercury parts as the Hardin Pump design was reconfigured to fit an additional wear plate. Can only be used on Hardin pumps 625-4102 and 625-4101.
|
|
625-4245 Replacement internal wear plate for Hardin Gen 7 and 8 Sea Pumps. NOTE: Will NOT replace factory Mercury parts as the Hardin Pump design was reconfigured to fit an additional wear plate. Can only be used on Hardin pumps 625-4102, 625-4101 and 625-4122.
|
|
625-4246 Replacement rear wear plate for Hardin Gen 7 Sea Pumps. NOTE: Will NOT replace factory Mercury parts as the Hardin Pump design was reconfigured to fit an additional wear plate. Can only be used on Hardin pumps 625-4102 and 625-4101.
|
|
625-4247 Replacement small snap ring for Hardin Gen 7 Sea Pumps. NOTE: Will NOT replace factory Mercury parts as the Hardin Pump design was reconfigured to fit an additional wear plate. Can only be used on Hardin pumps 625-4102 and 625-4101. 2 needed per pump.
|
|
625-4248 Gasket, GEN 7 Sea Pump
Fits Stainless Steel Gen 7 Sea Pump #625-4102
|
|
625-4011
- Replaces Impellers on Hardin Ram Force, Multi-Stage, Lifetime Series Pumps.
- D Shaped Shaft AKA "Single Flat"
- 8 Vane Impeller
- Replacement Impeller For Mercury OEM Sea Pumps
- Replaces OEM Mercruiser # 47-59362T1
|
|
625-1153 Replacement o-ring for Hardin Gen 7 Sea Pumps. NOTE: Will NOT replace factory Mercury parts as the Hardin Pump design was reconfigured to fit an additional wear plate. Can only be used on Hardin pumps 625-4102 and 625-4101.
|
|
625-4263 Replacement Pulley Mandrel only for Hardin Gen 7 Sea Pumps. NOTE: Will only work with Hardin pulley #625-4262. Can only be used on Hardin pumps 625-4102 and 625-4101. Inside Diameter 0.745"
|
|
625-4262 Replacement 5.5" Pulley only for Hardin Gen 7 Sea Pumps. NOTE: Will only replace factory 5.5" Mercury pulleys and requires mandrel #625-4263. Can only be used on Hardin pumps 625-4102 and 625-4101.
|
|
900-31AN-STSS 5/16" Stainless Steel Washer.
|
|