Place Diverters, Jetovators & Controls - Trim Indicators & Controls

Bluetooth Controller for Bluewater Push Button Switches - Control up to 4 Functions

This control box is paired with a transmitter that is operated entirely by bluetooth. The transmitter will work up to 30 ft. away from the control box, The transmitter will operate drive trim, trim tabs or any other momentary switch application. DOES NOT includes switches

The switch transmitter requires a 12 volt power source and the draw is less than 5 amps. Each transmitter input is activated using +12 volts so they are compatible with any type of switch, including Bluewater. The Controller also requires a 12 volt power source with a maximum draw of up to 10 amps per switched load. Switched loads greater than 10 amps will require an external relay. Each switched output will change to + 12 volts when activated. Please note that the enclosures are not waterproof or ignition protected.

Each controller and transmitter pair have matching serial numbers so they must be kept together. The pairing uses an encrypted code and cannot be undone, or hijacked in the field. If a system requires repair we will need both the controller and the switch transmitter returned to MDC. Also, you can install as many of these systems in a single boat as you want, they will all operate independently and will not interfere with each other.

Bluetooth Operated Paddle Trim Kit for 3/4" Tapered Shaft Mount

This paddle trim mounts to any 3/4” tapered shaft with keyway. Add a race inspired trim control quick and easy with this kit, no wires needed!

Steering Wheel Mounted Trim Switch, Carbon Fiber Top Plate, Bluetooth Operation, Aircraft Switches

This control box is paired with a switch that is operated entirely by Bluetooth. The switch will work up to 30 ft. away from the control box, The switch will operate drive trim, trim tabs or any other momentary switch application. DOES NOT include a mounting plate. This model contains aviation quality control switches and a carbon fiber top plate. Each switch pod requires one control box.

Steering Wheel Mounted Trim Switch, Bluetooth Operation

This control box is paired with a switch that is operated entirely by bluetooth. The switch will work up to 30 ft. away from the control box, The switch will operate drive trim, trim tabs or any other momentary switch application. DOES NOT include a mounting plate. Each switch pod requires one control box.

Steering Wheel Mounted Trim Switch, Billet Aluminum, Polished with Curly Cord

Billet aluminum trim switches designed to fit most steering wheels with simple two bolt drill mounting. Dual Switches.  Trim switch comes in polished finish. DOES NOT include a mounting plate.

Steering Wheel Mounted Trim Switch & Diode Kit for use with Hydraulic Place Diverter

Don't want to take your hands off that steering wheel on those high speed runs or maybe you're just looking for more convenience then this is the answer This water resistant Billet Aluminum switch can be attached directly to your steering wheel.

Steering Wheel Mounted Trim Switch, Black Plastic, with Curly Cord

This trim switch is designed to fit most steering wheels with simple two bolt drill mounting. Dual Switches. Put trim switches on steering wheel for convenience. Allows driver to keep both hands on the steering wheel for safety.  Weatherproof rubber booted switches. Rugged urethane coiled cord. Can be used for trim control or jack plate control. Mounts easily on steering wheel spokes by drilling mounting holes If you do not want to drill holes you can purchase rear mounting plates separately. DOES NOT include a rear mounting plate.

Steering Wheel Mounted Trim Switch Kit , Black Plastic, with Curly Cord and Diode Kit

This trim switch is designed to fit most steering wheels with simple two bolt drill mounting. Dual Switches. Put trim switches on steering wheel for convenience. Allows driver to keep both hands on the steering wheel for safety.  Weatherproof rubber booted switches. Rugged urethane coiled cord. Can be used for trim control or jack plate control. Mounts easily on steering wheel spokes by drilling mounting holes If you do not want to drill holes you can purchase rear mounting plates separately. DOES NOT include a rear mounting plate. Kit comes with Diode Kit.

Mounting Plate for 151-1200 Trim Switch

Plate and 4 screws for mounting a 151-1200 Trim Switch to most steering wheels.

Diode Kit Only

For Optional Steering Wheel Mounted Trim Switch.

Place Diverter Toggle Switch

This toggle switch is what comes with the Place Diverter hydraulic kit. It mounts to your dash, for easy finger tip control of your hydraulic nozzle.

Place Diverter Trim Indicator Replacement Cable

Replacement for the cable from the 151-25114 trim kit. Cable is 5' in length.

Trim Indicator Kit

With this fabulous kit you can now know exactly how your jet drive is trimmed by simply seeing it on a gauge, as opposed to constantly turning around to try and visualize your diverter output and drive at the same time Includes gauge, sender, and hardware.

For complete control of engine trim and tilt, trim tabs, jackplates, PowerPole(R) and other on board systems, the innovative Paddle Trim system is the answer.

Adaptable to existing front mount hydraulic and tilt helms, the Paddle Trim is ergonomically designed to allow the driver to make precise adjustments to the attitude of the boat or other systems without removing his hand from the steering wheel.

FEATURES

• Available both in single and dual versions (for either two equal or two different outputs). 
• Both single or dual paddle can be positioned at various angles for the most confortable choice. 
• Equipped with one water proof “MOM.ON-OFF-MOM.ON switch ( 2 switches on dual version). 
• Max load 5 Amp @ 12VDC.
• For loads exceeding 5 Amp we recommend the use of the KTR - 42860S kit relay.
• Uflex^® trim tabs require the use of the KTR - 42860S kit relay.
• Suitable for any kind of steering wheel dish. Max wheel dia. 400 mm (15.7”). 
• Easy to install on the following Ultraflex^® steering systems: front and tilt mount hydraulic helms and tilt mount mechanical helms
• Wiring harness, labels and mounting hardware kit are included. The mounting plate, which differs between front and tilt mount. Installation, is ordered separately.

For complete control of engine trim and tilt, trim tabs, jackplates, PowerPole(R) and other on board systems, the innovative Paddle Trim system is the answer.

Adaptable to existing front mount hydraulic and tilt helms, the Paddle Trim is ergonomically designed to allow the driver to make precise adjustments to the attitude of the boat or other systems without removing his hand from the steering wheel.

FEATURES

• Available both in single and dual versions (for either two equal or two different outputs). 
• Both single or dual paddle can be positioned at various angles for the most confortable choice. 
• Equipped with one water proof “MOM.ON-OFF-MOM.ON switch ( 2 switches on dual version). 
• Max load 5 Amp @ 12VDC.
• For loads exceeding 5 Amp we recommend the use of the KTR - 42860S kit relay.
• Uflex^® trim tabs require the use of the KTR - 42860S kit relay.
• Suitable for any kind of steering wheel dish. Max wheel dia. 400 mm (15.7”). 
• Easy to install on the following Ultraflex^® steering systems: front and tilt mount hydraulic helms and tilt mount mechanical helms
• Wiring harness, labels and mounting hardware kit are included. The mounting plate, which differs between front and tilt mount. Installation, is ordered separately.