Hardin Marine

1" Stainless "Y" Style Fitting

These all stainless steel "Y" style water divider fittings arecommonly used when plumbing 4-port thermostat housing down to 2 hoses for wateroutlet to the exhaust manifold connection.

• Adjustable Tube style design allows them to be tailor-fitted to your application.
• Accepts a standard 1.25" NPT Female Fitting
• Easy 4-bolt attachment.
  
• Adjust bolts on bracket to raise or lower pickup
• 316L Stainless Steel

1.4 HP Chrome Mini Super Starter

This chrome plated high performance mini starter has been a leading choice of performance boaters. Top quality components along with a ball bearing design produces a starter that is durable even in hot temperature conditions. This starter is rated at 1.4 HP of cranking power which is nearly 40% stronger than traditional OEM Delco style starters

USCG Approved (SAE J1171)

These stainless steel fittings are designed to thread into the end the valve spring oilers (755-8482). This allows you to adapt to standard -4 AN fittings for plumbing. Sold Each.

1/16" x 3/4" Cotter Pin - Stainless

Bend prongs outward to secure. Also known as split pins, they have one prong slightly longer than the other so they’re easy to open.

Type 316 and 18-8 stainless steel may be mildly magnetic. Type 316 pins are more corrosion resistant than 18-8 stainless steel pins.

1/2" Left Hand Male Rod End

These rod ends are all stainless steel

Marine Fuel Line Hose 1/2" I.D.

This is true USCG approved marine grade fuel hose Don't take any chances with your investment Use only marine grade hose.

Fuel line hose is sold by the foot, i.e add quantity of 6 for 6 ft. of hose.

Hose comes in maximum of 50 feet sections. Please specify if you want sections cut into specific lengths when ordering over 50 feet.

Shields Reinforced PVC Tubing is constructed with clear polyester FDA formula vinyl walls with a red tracer and can be best into a gradual radius. This tubing is ideal for use with pressurized water systems, drain line, wash down pump connections and head intake.

Vent / Bilge hose is sold by the foot, i.e add quantity of 6 for 6 ft. of hose.

Hose comes in maximum of 50 feet sections. Please specify if you want sections cut into specific lengths when ordering over 50 feet.

This hose is commonly used for venting or bilge dump.

Vent / Bilge hose is sold by the foot, i.e add quantity of 6 for 6 ft. of hose.

Hose comes in maximum of 50 feet sections. Please specify if you want sections cut into specific lengths when ordering over 50 feet.

316L Stainless Steel Fitting
1/2" NPT Pipe Plug

We Offer the most complete line of chrome plated brass and custom fabricated stainless steel fittings available anywhere. All of these fittings are sure to simplify your plumbing job and add a tasteful finishing touch.

1/2" Right Hand Male Rod End

These rod ends are all stainless steel

1/2" Stainless Eyelet

These are high grade stainless eyelets in 1/2" diameter. The eyelets can also be used on the transoms or bow of boats for tie downs or tow hooks. 3" of thread length. Dimensions: Size: 1/2", Overall Length: 4-3/4", Threaded Length: 3", Pin Center to Center: 1-7/8"

This has to be one of the coolest and simplest stream lined inventions to come along in recent times. High water pressure spikes plague numerous boats and cause catastrophic engine damage. Until now your only option was an independent pressure relief valve that you then had to plumb to a water dump to discharge the water. Thanks to the Hardin Marine team they have taken the best high flow water valve design and integrated it into a common water dump.

These dumps feature a sleek design as well as unique wrench flats machined into the body aiding in assembly during a one person installation. Constructed from 316L stainless steel. This model provides a 1/2 NPT female thread allowing for any arrangement of possible fitting and hose connections. The unit features a stainless tulip style valve that is spring loaded. The units come preset at approximately 10psi.

• 1-7/16" Flange Diameter
• 1/4" Flange Height 
• 1-1/8" Shaft Outside Diameter
• 3" Overall Length
• 1/2" NPT Internal Thread
• Pre-set at Aprox. 10lb Pressure Relief, not adjustable.
• Approx. Flow Rate (gallons per minute) 10 psi=7 GPM, 15 psi= 13 GPM, 20 psi=19 GPM

Marine Fuel Line Hose 1/4" I.D.

This is true USCG approved marine grade fuel hose Don't take any chances with your investment Use only marine grade hose.

Fuel line hose is sold by the foot, i.e add quantity of 6 for 6 ft. of hose.

Hose comes in maximum of 50 feet sections. Please specify if you want sections cut into specific lengths when ordering over 50 feet.

This hose is commonly used for venting or bilge dump.

Vent / Bilge hose is sold by the foot, i.e add quantity of 6 for 6 ft. of hose.

Hose comes in maximum of 50 feet sections. Please specify if you want sections cut into specific lengths when ordering over 50 feet.

1/4" NPT Flexible Dipstick Kit

A unique flexible dipstick tube assembly allows easy access and a universalfit, making it easy to work around marine exhaust systems. The pan musthave a pipe thread provision to work with this dipstick.

20" Long Tube

1/4" NPT Stainless Steel Pipe Plugs

1/4"-28 Button Head Allen Bolt, 0.25" Long, Coarse Thread.

1/8 NPT Brass Allen Plug

• Replacement fitting for Oil Line Thru Hull #137-8066
  
• Sold Each

10 Amp Mercury Style Circuit Breaker

These breakers are the most common marine units used on factory style as well as aftermarket marine engines and harnesses. Be careful not to exceed the original amperage rating of your existing harness.

10" Billet Aluminum Euro Style Handle - Each

We've got them - the latest in billet handles. These Euro StyledHandles feature smooth contoured shapes and edges. These units use thesame mounting holes as the traditional handles and vents so they areperfect fora new boat building project or they will retro-fit the traditionalhandles andvents manufactured by Hardin Marine.

*Note- These grab handles are 11-1/2" long with 10" bolt centers. Internal threads are 5/16-18"

See what each of our powder-coated finishes (both flat and glossy) look like under different lighting here!