780-1050
- 1-1/4" Slip-On
- Outer Diameter 2.23"
- Overall Length 3.8"
- Polished Stainless Steel
- Stainless Steel main body and flange.
- Includes Nut and Soft Washer.
|
|
780-1020
- 1-1/4" Slip-On
- Outer Diameter 2.23"
- Overall Length 3"
- Polished Stainless Steel
- Stainless Steel main body and flange.
- Includes Nut and Soft Washer.
|
|
462-34-ARG1250SBSPP Standard single strainers. No tie rods or leaks under pressure or vacuum. Quick and easy mounting system allowing removal of strainer without tools. #304 Stainless steel filter basket. O-ring seals at strainer cap and between strainer head and sight glass. See-thru screw-on strainer cap allows easy, no-tools maintenance. Spanner wrench holes in cover allow the use of SW-2531 wrench. Install with pipe or hose. Do not use chemical or abrasive cleaners on sight glass. NOT TO BE USED IN POTABLE WATER SYSTEMS. Ports: 1 1/4" NPT, Basket: Stainless, A: 10.6", B: 5.8", C: 6.5", D: 2.3" Standard single strainers. No tie rods or leaks under pressure or vacuum. Quick and easy mounting system allowing removal of strainer without tools. #304 Stainless steel filter basket. O-ring seals at strainer cap and between strainer head and sight glass. See-thru screw-on strainer cap allows easy, no-tools maintenance. Spanner wrench holes in cover allow the use of SW-2531 wrench. Install with pipe or hose. Do not use chemical or abrasive cleaners on sight glass.NOT TO BE USED IN POTABLE WATER SYSTEMS.
|
|
462-34-TH125W Should have threaded portion cut to proper length considering hull and butt block thickness. Consider thread depth when using a seacock. Sealant is recommended between hull and thru-hull flange. Has locknut with bonding screw. Comes with nut. NOT TO BE USED IN POTABLE WATER SYSTEMS. Thread: G 1 1/4", A: 2.90", B: 0.30", C: 2.62" Should have threaded portion cut to proper length considering hull and butt block thickness. Consider thread depth when using a seacock. Sealant is recommended between hull and thru-hull flange. Has locknut with bonding screw. Comes with nut.NOT TO BE USED IN POTABLE WATER SYSTEMS.
|
|
462-87-CHOGSET Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length 36 sq." bearing area x 35 psi 1,260 lbs. Is bearing load capacity Shaft: 1-1/4" dia., OD: 1-1/2", Length: 5", Metal Wall: 1/32", Johnson Name: BIND**, BF Goodrich Name: Kibble Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length = 36 sq. Inch bearing area 36 sq. Inch bearing area x 35 psi = 1,260 lbs. Is bearing load capacity
|
|
462-87-CHUB Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length 36 sq." bearing area x 35 psi 1,260 lbs. Is bearing load capacity Shaft: 1-1/4" dia., OD: 1-3/4", Length: 5", Metal Wall: 1/8", Johnson Name: BIRD, BF Goodrich Name: Kidnap Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length = 36 sq. Inch bearing area 36 sq. Inch bearing area x 35 psi = 1,260 lbs. Is bearing load capacity
|
|
462-87-COD Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length 36 sq." bearing area x 35 psi 1,260 lbs. Is bearing load capacity Shaft: 1-1/4" dia., OD: 2", Length: 5", Metal Wall: 1/8", Johnson Name: BITE*, BF Goodrich Name: Kiano Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length = 36 sq. Inch bearing area 36 sq. Inch bearing area x 35 psi = 1,260 lbs. Is bearing load capacity
|
|
462-88-1461146 Shields Vac Extra Heavy Duty/Commercial Grade Hose has a smooth cover and clear FDA formula PVC with a white vinyl helix. It is rated for full vacuum and is resistant to mild chemicals and saltwater. This hose is primarily used for bilge pump intake and discharge, potable water tank fill, drains (sinks, shower, and scupper), livewell intake and drain, and sanitation (intake, vent and pump out). This hose is utilized for below the waterline connections.Do not use ethylene glycol based antifreeze in hose. Do not use in pressurized water systems. ID: 1-1/4", Length: 50' Shields Vac Extra Heavy Duty/Commercial Grade Hose has a smooth cover and clear FDA formula PVC with a white vinyl helix. It is rated for full vacuum and is resistant to mild chemicals and saltwater. This hose is primarily used for bilge pump intake and discharge, potable water tank fill, drains (sinks, shower, and scupper), livewell intake and drain, and sanitation (intake, vent and pump out). This hose is utilized for below the waterline connections.
|
|
462-9-0835007PLB Includes: thru-hull, hose adapter, drain plug, four pre-drilled mounting holes and bonding screw. Incorporates a plastic ball and seat assuring a tight seal and ease of operation and drain plugs for winterizing. Handles are easily removed. Overall height is measured from the top of the hose adapter to the bottom of the flange. Connector: 1-1/4", Hose: Straight, Height: 6-1/4", Flange: 4-7/8" dia., Bolt: 3/8" Includes: thru-hull, hose adapter, drain plug, four pre-drilled mounting holes and bonding screw. Incorporates a plastic ball and seat assuring a tight seal and ease of operation and drain plugs for winterizing. Handles are easily removed. *Overall height is measured from the top of the hose adapter to the bottom of the flange. UL Listed. NOT TO BE USED IN POTABLE WATER SYSTEMS
|
|
462-236-H140114P72 "304 Stainless Steel, .040 gauge. Holes are drilled on 2" centers with no stagger. Great for doors, large cabinets and hatches. Available in 6' lengths only. NOTE: A UPS/FedEx overlength/packaging fee may apply to this product."
Finish: Polished, Length: 6', Width: 1-1/4", Fastener: #5, Pkg.: Bulk
Sold: Each
|
|
462-9-035006ADPC "Available in plain or chrome plated bronze, these fittings have a hose barb connection and are recommended for use above the waterline only. The flange is machined to fit the hull tightly and grooved to retain bedding compound. Minimum hull thickness 3/8"." Hose: 1-1/8", Flange: 2-1/4", Max Hull Thickness: 1-3/4" Sold: Each
|
|
462-9-0328DP6A Molded white plastic with broad flange. For use with hose. Not recommended for use below waterline. Hose: 1-1/8", Flange: 2-1/4" OD", Max Hull Thickness: 1-1/2" Sold: Each
|
|
780-1045
- 1-1/8" Slip-On
- Outer Diameter 2.20"
- Overall Length from flange 3.65"
- Polished Stainless Steel.
- Stainless Steel main body and flange.
- Includes nut and gasket.
|
|
780-1015
- 1-1/8" Slip-On
- Outer Diameter 2.20"
- Overall Length 2.15"
- Polished Stainless Steel.
- Stainless Steel main body and flange.
- Includes nut and gasket.
|
|
780-300 1-1/8" Plastic Water Dump - White
- Color: White
- Hose Size: 1-1/8"
- Flange OD: 1-3/4"
- Thread Length: 1-1/2"
- Overall Inside Length: 3-1/8"
- Quantity: Sold Individually
|
|
462-87-CAMA Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length 36 sq." bearing area x 35 psi 1,260 lbs. Is bearing load capacity Shaft: 1-1/8" dia., OD: 1-1/2", Length: 4-1/2", Metal Wall: 1/16", Johnson Name: BEAM**, BF Goodrich Name: - Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length = 36 sq. Inch bearing area 36 sq. Inch bearing area x 35 psi = 1,260 lbs. Is bearing load capacity
|
|
462-87-CATFISH Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length 36 sq." bearing area x 35 psi 1,260 lbs. Is bearing load capacity Shaft: 1-1/8" dia., OD: 1-3/4", Length: 4-1/2", Metal Wall: 1/8", Johnson Name: BEND*, BF Goodrich Name: Kerny Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length = 36 sq. Inch bearing area 36 sq. Inch bearing area x 35 psi = 1,260 lbs. Is bearing load capacity
|
|
462-87-CARP Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length 36 sq." bearing area x 35 psi 1,260 lbs. Is bearing load capacity Shaft: 1-1/8" dia., OD: 1-5/8", Length: 4-1/2", Metal Wall: 1/8", Johnson Name: BELT, BF Goodrich Name: Kersey Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length = 36 sq. Inch bearing area 36 sq. Inch bearing area x 35 psi = 1,260 lbs. Is bearing load capacity
|
|
462-88-1461186 Shields Vac Extra Heavy Duty/Commercial Grade Hose has a smooth cover and clear FDA formula PVC with a white vinyl helix. It is rated for full vacuum and is resistant to mild chemicals and saltwater. This hose is primarily used for bilge pump intake and discharge, potable water tank fill, drains (sinks, shower, and scupper), livewell intake and drain, and sanitation (intake, vent and pump out). This hose is utilized for below the waterline connections.Do not use ethylene glycol based antifreeze in hose. Do not use in pressurized water systems. ID: 1-1/8", Length: 50' Shields Vac Extra Heavy Duty/Commercial Grade Hose has a smooth cover and clear FDA formula PVC with a white vinyl helix. It is rated for full vacuum and is resistant to mild chemicals and saltwater. This hose is primarily used for bilge pump intake and discharge, potable water tank fill, drains (sinks, shower, and scupper), livewell intake and drain, and sanitation (intake, vent and pump out). This hose is utilized for below the waterline connections.
|
|
615-552-112012 -12 AN 120° Fixed Hose End
- Available: (6) Six
- Condition: Overstock
|
|