450-1100A Weldon 145 GPH Inline Fuel Pump
- 170 GPH at 15psi
- 145 GPH at 30psi
- -10 inlets and outlets
Billet high performance fuel pumps for carbureted or injected engines. These pumps are machined from billet aluminum. They are compatible with Weldon 2040 series regulators and with 14000 dial-A-Flow. They provide consistent performance with no fall-off flow. The blades are self compensating for wear. These pumps have a rated flow of 170 GPH at 15psi and 145 GPH at 30psi and are suitable for use on engines up to 1100 HP (efi) or 1300 HP (carb).
NOT USCG APPROVED
|
|
450-2046 Weldon 15 PSI 4 Port Adjustable Fuel Regulator
Revolutionary Tool-Free pressure adjustment -- allows for more precise control of base fuel pressure with single hand adjustability.
Features:
- Stainless Steel Poppet and Delrin seat comprise the most modern cartridge design and allows for the most consistent fuel delivery in the industry
- "Creep" characteristics are unaffected by outlet port configuration, allowing the use of as many or as few ports as desired
- Can be used in single, dual, and "split" carb'd applications without compromising performance
- Industry Standard -- mounting and port configuration for easy installation
- Largest, least restrictive internal flow chamber
- Innovative valve cartridge has the largest flow paths to support higher fuel flows
- Unique Valve seat design provides smooth and predictable valve response with the most stable fuel delivery
- Resilient Teflon diaphragm is compatible with all racing fuels
- Designed to maintain steady fuel delivery during dramatic changes in fuel demand, such as WOT conditions, boost application and gear changes
- Adjustable from 4-15 psi
- 1/8" NPT Gauge Port
- 1/8" NPT manifold pressure reference port (filtered vent -- supplied)
- Fuel pressure increases on a 1:1 ratio with boost
- One -10 Inlet with four -6 pressure ports
- Replaceable / interchangable internal components
For use with all Weldon Pump and regulator combinations, as well as pumps from other manufactures
|
|
450-2040-281-A-15 Bypass Fuel Regulator
Provides a fast response rate, for stable fuel delivery, for the most demanding requirements. These regulators maintain steady fuel delivery duringdramatic changes in fuel demand, such as WOT conditions, boostapplication and gear changes. Hardened steel ball, replaceable steel seat, and Fluorosilicone diaphragm. Compatible with most racing fuels including ethanol and methanol. Fuel pressure increases on a 1:1 ratio with boost. User serviceable, replaceable, and interchangeable internal components.
- .281" bypass orifice
- 1/8" NPT Gauge Port
- 1/8" NPT manifold pressure reference port
- (2) -10 pressure ports
- -8 return port
|
|
450-2345 Weldon 250 GPH Fuel Pump
Maximum Horsepower
2000 hp @ 14 VDC EFI (1000 hp on Methanol)
2400 hp @ 16.5 VDC EFI (1200 hp on Methanol)
GPH/PSI Range:
200-250 GPH / 0-80 PSI
Considerations:
If your actual horsepower is close to the Max Hp limit and/or you are considering power adder, see part# 34706 or 34712 Mechanical Pump
Features:
- All billet body pumps are 100% serviceable/repairable
- Self Priming
- Pump may be mounted above fuel cell
- Vertical or horizontal mount
- Breakaway coupling prevents pump/motor damage in the event of fuel contamination
- All internal components are 100% metallic
- No plastics or composite materials. Our internal pumping elements are made of high speed tool steel and bronze. This results in the longest lasting, highest quality, most durable pumps available.
- Body machined from billet aluminum
- For carbureted and injected engines
- Provides Consistent Performance with no fall-off in flow
- Precise fuel delivery
- Blades self-compensating for wear
Weldon Pump has introduced a new quieter, lower speed, long lived fuel pump that will support 2500 HP at 70PSI. This pump features a new hex shape and is compatible with the 14000 Dial-A-Flow controller. The pump provides a -12 inlet and a -10 outlet. The rated flow is 250 GPH and the rated pressure is 70 PSI. The pump weighs 6 pounds.
|
|
450-600A Weldon 55-80 GPH Inline Fuel Pump
- 55-80 GPH/0-95 PSI
- -10 inlet and outlet
- Leak free O-Ring ports
Weldon has upgraded the 600-A flow-through continuous-duty fuel pump with -10 inlet and outlet ports and fitted it with revised end caps. Its bigger ports allow the pump to draw more fuel, to deliver more fuel, and to do this at reduced amperage draw. The new 600-A is distinguished by its black colored end-caps. Designed for up to 600 to 700 horsepower (fuel injected) or 800 horsepower (carbureted). At 42 PSI (most common EFI setting) the 600-A delivers more than 72 GPH with fewer than a 5 amp draw.
NOT USCG APPROVED
|
|
462-57-86050 12 volt - 50 amp
Internal regulator
Single groove pully included - 12 volt - 50 amp
- Internal regulator
- Single groove pully included
: Sold: Each
|
|
This Part has options, please click the button below to order.
542-36889CN 36889CN Westerbeke Heat Exchanger 3" x 19" w/ mounts for W70 engine.
|
|
This Part has options, please click the button below to order.
542-36890CN 36890CN Westerbeke Heat Exchanger. Westerbeke 70-100 / 25-32KW Westerbeke 100 - Sea Water System and Alternator: Westerbeke 70-100 / 25-32KW Westerbeke 100 - Fresh Water Cooling System – Rear.
Same as Westerbeke 32318CN.
|
|
This Part has options, please click the button below to order.
542-36895CN 36895CN Westerbeke Heat Exchanger 3 KW 2" x 14-1/2" used on Westerbeke 10TWO / 3KW Cooling System.
|
|
This Part has options, please click the button below to order.
542-36897CN 36897CN Westerbeke Heat Exchanger 3" Diameter x 16" long. For Westerbeke Gasoline Generator models:
8.0TWG, 11.0TWG.
Replaces Westerbeke 36897CN and 34644CN.
|
|
This Part has options, please click the button below to order.
542-36898 CN 36898CN Westerbeke Heat Exchanger Gen Set 12KW w/ mounts used on Westerbeke 46 / 15.0 BTD - 60 Hz / 12.0 BTD - 50 Hz Cooling System.
Replaces Westerbeke 34790CN.
|
|
This Part has options, please click the button below to order.
542-36899CN 36899CN Westerbeke Heat Exchanger 18 21A 27A 33A 38A w/ mounts, cupro nickel (CuNi) core. Westerbeke 35B Three / 38B Four / 42B Four Propulsion - Cooling System: Universal 44A 44B 12.5 BTDB-60 9.4 BTDB-50 15.0 BTDC-60 12.0 EXHAUST MANIFOLD & HEAT EXCHANGER - 44A/B: Westerbeke 35C 35D 8.0 BTDA-60 6.0 BTDA-50 10.0 BTDA-60 7.5 B EXHAUST MANIFOLD & HEAT EXCHANGER - 35C/D Replaces 24308 for W70 Engine.
|
|
This Part has options, please click the button below to order.
542-36900CN 36900CN Westerbeke Heat Exchanger 2" Diameter; 17-1/2" long w/ mounts.
|
|
This Part has options, please click the button below to order.
542-36902CN 36902 Westerbeke Heat Exchanger for Westerbeke Gasoline Generator models:
8.5BTG, 8.5BTGA, 12.5BTG, 15.0BTG, 15.0BTGA.
Can be used to replace Westerbeke 36902.
|
|
This Part has options, please click the button below to order.
542-36903CN 36903CN Westerbeke Heat Exchanger Gen Set 3" Diamter x 16" long w/ mounts. Used on Westerbeke 35B Three / 38B Four / 42B Four Generator - Cooling System.
Same as Westerbeke 35135CN.
|
|
This Part has options, please click the button below to order.
542-36905CN 36905CN Westerbeke Heat Exchanger with cupro nickel (CuNi) core, used on W52 Generator.
Replaces 24308 for W52 Engine.
|
|
This Part has options, please click the button below to order.
542-37564CN 37564CN Westerbeke Heat Exchanger for the 20B2 and 30B3 cooling systems.
|
|
This Part has options, please click the button below to order.
542-37587CN 37587CN Westerbeke Heat Exchanger Heat Exchanger w/ mounts for the 12C2, 20B2 and 30B3 cooling systems.
|
|
This Part has options, please click the button below to order.
542-38147CN 38147CN Westerbeke Heat Exchanger, for Westerbeke 5BCD 5BCDA 7.6 BTD. Copper Nickel Core.
|
|
This Part has options, please click the button below to order.
542-43282CN 43282CN Westerbeke Heat Exchanger fits Westerbeke Gasoline Generator models:
4.5BCGB, 4.5BCGTC, 4.5BCGT E, 7.0BCGB, 7.2BCGTC, 7.2BCGTE, 9.6BCGTC, 9.6BCGTE.
|
|
