Batteries & Accessories - Battery Switches

Add a 12 volt receptacle to your boat so you can use 12v accessories such as battery / phone chargers

Remote Dual Battery Switch

• Ignition protected - Safe for installation aboard gasoline powered boats
  
• Case design allows surface, front panel, or rear panel mounting
  
• Isolating cover with snap-on sections protects rear contacts
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" (22.22mm) stud length to accept multiple cable terminals
  
• Ideal for marine or RV applications
  
• All non-corrosive marine grade metals
  
• Molded in durable reinforced polycarbonate
  
• Tactile textures indicate knob position by feel only
  
• Label with international ON/OFF legends
  
• Removable key or knob remains positively retained
  
• ICON label set included for circuit identification
• Same as Blue seas 6006 model

Remote Battery Selector Switch

• Ignition protected - Safe for installation aboard gasoline powered boats
  
• Case design allows surface, front panel, or rear panel mounting
  
• Isolating cover with snap-on sections protects rear contacts
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" (22.22mm) stud length to accept multiple cable terminals
  
• Ideal for marine or RV applications
  
• All non-corrosive marine grade metals
  
• Molded in durable reinforced polycarbonate
  
• Tactile textures indicate knob position by feel only
  
• Label with international ON/OFF legends
  
• Removable key or knob remains positively retained
  
• ICON label set included for circuit identification

Remote Two Circuit Battery Selector Switch

• Ignition protected - Safe for installation aboard gasoline powered boats
  
• Case design allows surface, front panel, or rear panel mounting
  
• Isolating cover with snap-on sections protects rear contacts
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" (22.22mm) stud length to accept multiple cable terminals
  
• Ideal for marine or RV applications
  
• All non-corrosive marine grade metals
  
• Molded in durable reinforced polycarbonate
  
• Tactile textures indicate knob position by feel only
  
• Label with international ON/OFF legends
  
• Removable key or knob remains positively retained
  
• ICON label set included for circuit identification

Add a 12 volt receptacle to your boat so you can use 12v accessories such as battery / phone chargers

The Motorized Battery Switch has two modes of operation. Auto and Manual. There is a LED located on the battery switch to indicating Battery Switch Status.

Auto Operation: The Battery Switch moves from a state of "Auto Off" to "Auto On" when the remotely mounted switch is turned on. During the time that the battery switch is in "Auto On" mode, the "Auto On" LED is illuminated. Auto operation of the battery switch is not possible whilst in manual mode. If auto operation is attempted, the LED will flash for 3 seconds then stop. Knob must be returned to "Auto Off" before normal auto operation can continue.

Manual Operation: The automatic operation of this battery switch can be overridden at anytime by depressing the control knob and turning clockwise towards the "Man On" position or counter clockwise towards the "Man Off" position. During the time that the Battery switch is in "Man On" mode, the "Man On" LED is illuminated.

The Motorized Battery Switch has two modes of operation. Auto and Manual. There is a LED located on the battery switch to indicating Battery Switch Status. This is a Ground activated Battery Switch, Same as 516-9805-006-1 but this is activated by a ground, whereas the 516-9805-006-1 is activated by +12V.

Auto Operation: The Battery Switch moves from a state of "Auto Off" to "Auto On" when the remotely mounted switch is turned on. During the time that the battery switch is in "Auto On" mode, the "Auto On" LED is illuminated. Auto operation of the battery switch is not possible whilst in manual mode. If auto operation is attempted, the LED will flash for 3 seconds then stop. Knob must be returned to "Auto Off" before normal auto operation can continue.

Manual Operation: The automatic operation of this battery switch can be overridden at anytime by depressing the control knob and turning clockwise towards the "Man On" position or counter clockwise towards the "Man Off" position. During the time that the Battery switch is in "Man On" mode, the "Man On" LED is illuminated.

Remote Dual Battery Switch

These switches permits selection between either one of two batteries or operation of both batteries in parallel. Battery switches allow you to protect your battery from unsuspecting electrical draws.

USE COUPON CODE FREEBATTERYSWITCH TO GET THIS ITEM FREE WHEN PURCHASHING SELECT BILLET OR CAST ALUMINUM BATTERY BOXES. SEE RELATED ITEMS FOR ELIGIBLE BATTERY BOXES. NOTE: To take advantage of this offer, add an eligible battery box to your cart and then type the coupon code in the coupon code field at checkout, this will add switch to your cart at $0. Do not add switch to cart and then enter coupon code.

The VSS (Voltage Sensitive Switch) Motorized Battery Switch performs an automated paralleling function during charging, which allows two separate batteries to be charged as one.

• Auto Engagement of VSS: When the charging source is higher than 13.7VDC for more than 5 seconds, the VSS will engage.
• Auto Disengagement of VSS: When the battery drop under 12.2VDC, VSS will be disengaged.
• Same as BEP 58647

Emergency Parallel Function: The VSS Emergency Parallel Function can be operated through a remotely mounted momentary switch or button. The VSS will remain in parallel mode for 10 minutes. If after 10 minutes the voltage on either has not reached 13.0V the VSS will disengage. If the voltage reaches 13.0V on either battery the VSS will remain engaged and both batteries will continue to be charged. At any time depressing and holding momentary switch or button for 5 seconds will disengage the VSS.

Manual Override: The automatic operating of the VSS can be overridden at anytime by depressing the control knob and turning clockwise towards the "Manual On" position or anti clockwise towards the "Manual Off" position. Once the VSS attempts an automated function whilst in manual override, it determines it is in manual override (On or Off) and the LED will start flashing rapidly.

Remote Dual Battery Switch with Key Lock

These switches permits selection between either one of two batteries or operation of both batteries in parallel. Battery switches allow you to protect your battery from unsuspecting electrical draws.

Battery Terminal Disconnect Switch

One turn of the knob disconnects the battery and saves the solid state regulator and alternator when charging. Switch is rated at 100 amps for 12 or 24 DC use.