Hardin Marine

• Ultimate in a clean and functional installation.
• Designed for MSD 6M2L or New 6M3L Ignition Boxes
• Polished Billet Aluminum.
• Will mount on a Big Block Chevy Cylinder Head, port or starboard.
• Will also mount round coils or MSD Blaster SS coils.

• Ultimate in a clean and functional installation.
• Designed to sandwich between an MSD 6M2L, 6M3L, Max Volt MV-D6 or a Daytona Sensors Old Style CD-1 Control Box. New CD-1 Boxes have a different pattern.
• Satin Finished Stainless Steel.
• Will mount on a Big Block Chevy, Small Block Chevy, 455 Olds, and 460 Ford Cylinder Head.

Dana Replacement / Upgraded Trim Tab Ram

Replace the old worn out ram on your Dana Trim Tab with this polished 316L Stainless Steel version. This kit includes 2 rams and 4 hoses to reto-fit to the Dana trim tabs.

Dana Trim Tab Ram Rebuild Kit, Fits MOST Dana Trim Rams

Replace the O-rings and seals on your old worn out ram on your Dana Trim Tab. Kit fits MOST Dana Trim Rams but not all. Kit includes seal, wiper and 7 O-Rings. Because of the irregular changes on Dana Trim Rams over the years there is not guide to what model or year these will fit.

Delco PMGR Series Starter Clockwise Rotation

Fits 12-3/4" flywheel with parallel bolt pattern. MerCruiser, Marine Power & OMC late models. 12Volt - 11 tooth. MerCruiser #50-806963A4.

BRAND NEW STARTERS - ALL UNITS MEET OR EXCEED OEM SPECIFICATIONS
Please Note: Direction of rotation is determined as to viewing the starter from the drive end.

If you're looking for the best alternator, then look no further as this is it! This all new delco style alternator whips out 120 amps at 12 Volts and requires a 3 wire hookup. USCG approved. Also available in Chrome.

• 10-Si Style Alternator For Marine Gasoline Engines.
• 2" Mounting Foot
• Integral Regulator
• Ignition Protected SAEJ1171
• 3-Wire Hook-Up
• Red Wire Is For Sensor
• Black Wire Is For Excitation

If you're looking for the best alternator, then look no further as this is it! This all new delco style CHROME alternator whips out 120 amps at 12 Volts and requires only 3 wire hookup. USCG approved.

• 10-Si Style Alternator For Marine Gasoline Engines.
• 2" Mounting Foot
• Integral Regulator
• Ignition Protected SAEJ1171
• 3-Wire Hook-Up
• Red Wire Is For Sensor
• Black Wire Is For Excitation

Delco Style 94 Amp 10SI Single Wire Alternator

New Delco style marine alternator. This model is satin finish. The 94 AMP has a single self-exciting one wire hook-up with a negative ground. Used in many applications including Mercruiser, Volvo and more. Replaces Mercruiser #47456A1 and #78403A2.

Delco Style 94 Amp 10SI Single Wire Chromed Marine Alternator

New Delco style chromed marine alternator. The 94 AMP has a single self-exciting one wire hook-up with a negative ground. Used in many applications including Mercruiser, Volvo and more. Replaces Mercruiser #47456A1 and #78403A2.

"Deluxe" MSD / Hardin Digital Ignition Package - Chevy V8

This "Deluxe" ignition package is the most complete offering of its kind If you are looking for the very best and most complete system this is it Each kit consists of the following components:

• (1) Hardin Marine 620-3560 Billet Marine Distributor
• (1) MSD 6564 6-M32L Series Multi-Spark Ignition Control Box with Built-In Rev Limiter
• (1) Hardin 2222 High Vibration Coil
• (1) Hardin Marine 8 MM Spark Plug Wire Set
• (1) Hardin Marine 620-11219 stainless steel head mount bracket.

Over our 40 years of engine development we have worked with some of the worlds most innovative and technologically advanced company's From those relationships came many new alliances and product advancements such as the introduction of the "multiple spark discharge" ignition systems from Autotronics Controls. This advanced technology has produced an ignition system powerful enough to prevent spark plug fouling, faster RPM advancement, quicker acceleration, and increased peak horsepower, while greatly improving the overall drivability of any boat yet tough enough to withstand the harshest marine environments. These systems are 100% certified for marine use to comply with all USCG requirements. We are proud to be able to off to you the finest marine ignition system available today.

"Deluxe" MSD / Hardin Ignition Package - Chevy V8

This "Deluxe" ignition package is the most complete offering of its kind If you are looking for the very best and most complete system this is it Each kit consists of the following components:

• (1) Hardin Marine 620-8560 Billet Marine Distributor
• (1) MSD 6560 6-M2L Series Multi-Spark Ignition Control Box with Built-In Rev Limiter
• (1) Hardin 2222 High Vibration Coil
• (1) Hardin Marine 8 MM Spark Plug Wire Set
• (1) Hardin Marine 620-11220 stainless steel head mount bracket.

Over our 40 years of engine development we have worked with some of the worlds most innovative and technologically advanced company's From those relationships came many new alliances and product advancements such as the introduction of the "multiple spark discharge" ignition systems from Autotronics Controls. This advanced technology has produced an ignition system powerful enough to prevent spark plug fouling, faster RPM advancement, quicker acceleration, and increased peak horsepower, while greatly improving the overall drivability of any boat yet tough enough to withstand the harshest marine environments. These systems are 100% certified for marine use to comply with all USCG requirements. We are proud to be able to off to you the finest marine ignition system available today.

Not for use on Stock pumps Gen 8 Sea pumps with Gen 2 Rear Cover!

Deluxe Rebuild Kit for Gen 8 Sea Pump, Gen 1 Rear Cover

Rebuild a 625-4132 Stainless Steel Sea Pump with this kit. This deluxe kit includes wear plates, snap rings, seals, bearings, o-ring, impeller

Not for use on Stock pumps Gen 8 Sea pumps with Gen 1 Rear Cover!

Deluxe Rebuild Kit for Gen 8 Sea Pump, Gen 2 Rear Cover

Rebuild a 625-4132 Stainless Steel Sea Pump with this kit. This deluxe kit includes wear plates, snap rings, seals, bearings, o-ring, impeller

2" Depth Sounder Kit - White, Black or Stainless

• 2 1/16 hole size, Outer diameter 2 5/16.
• Plastic body.
• Includes Shoot thru or transom mount transducer
• Includes Non-corrosive hardware and brackets
• Gasket sealed lens and bezel to prevent fogging

Hardin Marine Depth gauge uses advanced algorithmic programming to increase accuracy and provide precision depth readings. For added safety, Hardin Marine's triple warning system alerts the boat operator to shallow water conditions in three ways - audible, red LED and blinking LCD icons.

The gauge comes with a 200kHz high-speed dual mount transducer that can be mounted on the transom or inside the hull making it easy to install on any style of boat.
Accurate depth readings are provided at boat speeds of up to 60 mph (95kph/50kts). A programmable keel offset automatically adjusts depth readings for the vessel’s draft requirements so boat owners will always know precisely what the depth is and how much clearance they have under the keel.

Hardin marine's Digital Depth Gauge provides precise depth readings in feet or meters (user selectable). The digital display reads depths in tenths from 2.5 to 99.9 feet (0.75m to 30m) and in one-foot (0.3m) increments from 100 to 200 feet (30m to 60m).Both upper and lower alarm ranges can be set from 3 to 200 feet (1m - 60m).
This attractive 2-inch (50mm) gauge is offered in Three color coordinated styles to match most Hardin marine gauge series. Depth information is delivered on a polarized, 1.65” X .78” (42mm x 20mm) LCD with a backlit dial and buttons.

Specifications: Case dia: 53mm Fascia dia: 60mm Depth: 62mm Power: 11-14Vdc Current drain: 40mA Nominal Transmit power: 250W (max) Depth range: 0.7m - 60.7m

This kit will allow you to use a standard trim gauge the reads with an ohm sender with three wire digital trim sender signals. The Adapter will provide power and ground for the sender and then convert the sender signal into a resistive output that that any brand of trim gauge will accept.

Mayfair electronics by Hardin Marine and Marine Design Corp have teamed up to bring the new generation of the Heads-Up indicator system to the marine industry. This new conversion system will replace your push-pull cables that have lots of slop due to the cable functionality . This new conversion system will utilize the Mayfair 0-5 volt stainless steel potted sender or the Mercury 3-wire trim sender. The custom design and proprietary software controller that drives the highly engineered, electric drive motor assemblies will mount in the same location as your push/pull cables. With this new conversion you will have a true accurate reading on your indicator sticks. The software will auto retract the heads up indicator sticks to a down position when you turn off your ignition. When the ignition is turned back on the indicator stick will automatically return to the position the drives or tabs were left at. Pair this system with the Drive Sync option of Marine Design you will always have your drives sync together for ultimate efficiency.

Direct Replacement 496/496HO Silencer System (pair)

• Each contains 1 pair of highly polished 316L direct replacement silencer tips
• 1 pair of external exhaust flappers.
• Sold in pairs.
• Hose Size: 4"
• Silencers are slip in style and can be installed and removed with single bolt.

This silencer system was specifically designed and tested to comply with the J-2005 SAE testing standards that are being rigorously implemented on national waterways. The apparent problem that the Mercury 496 & 496HO is an open exhaust configuration that does not comply with the latest noise level limits required by law. This can now be rectified with these direct replacement silencers. In recent testing by "Hot Boat" magazine this system dropped the noise level to a legal 85/86 decibels.

Dominator Holley 4500 Base Gasket

Double Groove V-Belt Alternator Pulley for use on alternators with round pulley shaft. 2-5/8" OD. Fits a .670" Round Shaft.

Dowel Keyway For Multi-Stage Sea Pump Mandrel.

• Constructed of Polished 316L Stainless Steel.
• 3/4" NPT Female Thread
• Outer Diameter 1-1/4"
• Overall Length 3-7/8"
• Overall Width 5-1/4"
• Perfect for intercooler, tailpipe, and even engine water discharge. 

Replacement Dual filter basket used on Swirl-A-Way Sea Strainers set up for dual filter baskets. Supercedes older stlye 620-913211 basket. For 10 inch Sea Strainers 620-913205 and 620-913206.

• 3" Wide x 3-1/2" Tall.
• Available with Red, White, Translucent or Black Switches.
• Panels available in Red, Blue, Purple, Black or Silver Carbon Fiber.
• REAL Carbon Fiber, not printed on.